Sound Insulation - Stiga Titan HYTT Montageanleitung

EN
• 4 screws through the enlarged holes lower
front.
6. Tighten the 12 screws with about 70 Nm.
7. Remove the lifting devices.
8. Fit the rear view mirrors and adjust for optimal
sight rearwards.
9. Connect the terminal to the earlier fitted
harness.
4.12FUSE BOX, CONNECTING
1. Loosen the distribution box's mounting plate by
removing the 2 screws (13:U) and fold out the
plate.
2. Assemble the enclosed fuse carrier (14:G) with
mounting plate to the distribution box's
mounting plate (ev. drill necessary holes).
3. See fig. 13. Connect three cables from the front
harness as follows:
• The red cable to terminal 8 in the machine's
fuse box.
• The brown cable to one of the terminals A-F
• The yellow-green cabel to earth.
4. Assemble the direction indicator
and the light relay (14:L). Drill necessary holes
and connect connections.
5. Connect the heting device cable to the actual
connector at the harness.
6. Reassemble the distribution box's mounting
plate.
4.13HEATING HOSES
The heating hoses are never allowed to
touch sharp or wearing objects of the
machine. Damage on the heating hoses
are leading to burning injuries and to
serious engine damages.
Fit the heating hoses as follows:
1. Drain the upper half of the cooling liquid with
help of a siphon or similar through the filling
hole. See the machine operators manual
according to the placings.
2. Dismount the plug in fig. 22 and fit the inlet
plug with tapered thread and hose connection in
the hole. Use a sealing compound on the thread.
3. Dismount the plug in fig. 23 and fit the banjo
fitting with screw and gaskets.
5. Connect the hoses to the connections and with
clamps and draw the hoses up to the heating
element:
• The hoses shall be drawn through the
articulating point together with the other
hoses and harnesses. See fig 24.
• To the right of the seat. See fig. 25
Check that the heating hoses never touches
sharp or wearing objects of the machine.
10
ENGLISH
6. Assemble the protective hose (25:S) and
7. Fix the hoses with bundle strips against the
8. Set the cabin heat to full heat and refill cooling
9. Continue to fill the cooling system according to
4.14REAR CASING
Fit the rear lower case. According to the two lower
attachment holes, two holes shall be drilled and
threaded into the lower beam.
Assemble the sealing ring to the fuel filling tube.
Check that it seals against the casing.

4.15SOUND INSULATION

4.15.1Steering pulpet
relay
(14:K)
Sound isolate the steering pulpet with 4 insulating
plates as follows:
1. Disassemble the steering pulpet rear casing by
2. See fig. 27. Assemble the 4 insulating plates (T,
4.15.2Mats
See fig. 28. Place 2 mats at the floor and 1 mat
standing against the plastic protecting left rear.
4.16DELIMITERS
The turning ability must be limited to 55° when the
cabin is fitted. Otherwise there is a risk that the
cabin collides with the engine casing. Assemble
the delimiters on both sides according to fig 29.
connect the hoses to the heating element.
frame, body or other harnesses at necessary
places.
liquid in the cooling system.
the machine operators manual.
If the sealing leakes, there is risk of fire
and deadly peril.
loosening the four screws. See fig. 26.
U, V, X):
T. Measures: 30x13 cm. Wrap this plate around
the upper part of the hydraulic hoses. Wrap
until the sealing between hoses and plate
becames optimal.
U. Measures: 30x13 cm. Fold the plate in
triplicate and place it in the empty space to
the left of the steering servo.
V.Measures: 30x10 cm. Place the plate against
the protecting plate and refit the protecting
plate.
X. Glue the plate at the front on the steering
pulpet upper part.
Assemble the delimiters properly.
Otherwise there is a risk of serious
damages to the cabin and engine casing.