Working Advice - Bosch PTA 2400 Originalbetriebsanleitung

OBJ_BUCH-940-005.book Page 14 Tuesday, January 10, 2017 3:00 PM
14 | English
Additionally required tools (not in delivery scope):
– Cross-head screwdriver
– Spanner
Assembling the Saw Stand
Carefully remove all parts included in the delivery from their
packaging.
Remove all packaging material.
Setting Up the Saw Stand (see figures A1 – A2)
Lay the saw stand upside down on the floor (legs facing
upward).
Push the locking pin 3 in and tilt the leg upward until the
locking pin can be heard to engage.
Repeat this workstep with the other three legs.
Turn around the saw stand to the working position.
The manufacturer logo must face toward the front so that it
can be read.
Ensure that the saw stand is stable and that all locking pins
have engaged.
The saw stand is easily aligned with the height-adjustable leg
4.
Loosen lock nut 14 and screw the leg in or out until the saw
stand is aligned level and all four legs face against the floor.
Mounting the Length Stop and Workpiece Support
(see figures B1–B2)
Screw the length stop 6 to the workpiece support 8 with
carriage bolt M6 x 46 and locking knob 7.
Insert the workpiece support 8 into the table extension 10.
Tighten the locking knob 9 to lock the workpiece support.
Repeat the worksteps with the second workpiece support.
Preparing the Saw Stand
Preparing the Attachment Sets (see figures C1–C3)
Place both attachment sets 1 on the saw stand in such a
manner that the labelling can be read.
Hand-tighten both locking knobs 5.
Place the retaining adapters 2 with the flat side facing up-
ward on both attachment sets and move them apart so that
the fastening holes 15 are aligned.
Guide two assembly-sliding plates 16 each (perpendicular,
with the flat side facing upward) from the rear into the guide
compartment of the attachment sets 1.
Move the assembly-sliding plates apart so that they are
aligned with the fastening holes 15.
Hand-tighten the attachment sets and retaining adapters
with the washers and hexagon bolts from fastening kit 12.
Afterwards, firmly tighten both locking knobs 5 of the attach-
ment sets.
Fastening the Power Tool to the Attachment Sets
(see figures D1–D3)
Position the power tool in the transport position. Notes on the
transport position are given in the operating instructions of
the respective power tool.
1 609 92A 1M9 | (10.1.17)
Position the power tool on the front retaining adapter in such
a manner that the front mounting holes on the power tool are
brought into alignment with the slots of the retaining adapter.
Screw the front retaining adapter and the power tool together
with the hexagon bolts, washers and wing nuts from the
fastening kit 13.
Position the rear retaining adapter in such a manner that the
rear mounting holes on the power tool are brought into align-
ment with the slots of the retaining adapter.
Screw the rear retaining adapter and the power tool together
with the hexagon bolts, washers and wing nuts from the
fastening kit 13.
Align the retaining adapters 2 uniformly.
The imprinted scale aides in adjusting the same clearance on
both sides.
Finally, firmly tighten all screws of fastening kit 12 (retaining
adapter) and all wing nuts of fastening kit 13 (power tool).
Operation

Working Advice

Do not overload the saw stand. Always observe the maximum
carrying capacity of the saw stand and the two table exten-
sions.
Always hold the workpiece firmly, especially the longer and
more heavy section. After cutting through the workpiece, the
centre of gravity may become dislocated in such an unfavour-
able manner that the saw stand tips over.
If possible, always place the workpiece on one or both work-
piece supports.
Extending the Saw Stand (see figures F1 – F2)
Long workpieces must be underlaid or supported at their free
end.
Place your long workpiece onto the saw table of the power
tool.
Loosen locking knob 17 and pull the table extension 10 out to
the desired clearance.
Due to locking pin 11, the table extension can only be pulled
out to the stop.
Retighten the locking knobs again.
Loosen locking knob 9 and adjust the height of the workpiece
support 8 so that the workpiece rests level.
The workpiece must be positioned level on the power tool's
saw table.
Retighten the locking knobs again.
Sawing Workpieces of the Same Length
(see figure G)
The material stop 6 can be used for easily sawing workpieces
to the same length.
Adjust the desired workpiece length. (see figures F1 – F2)
Loosen locking knob 7 and position the length stop 6 to the
desired clearance to the saw blade of the power tool.
Retighten the locking knobs again.
Bosch Power Tools