Bosch 3 600 HB3 0 Series Originalbetriebsanleitung Seite 19

OBJ_BUCH-3148-001.book Page 19 Thursday, September 28, 2017 10:53 AM
When the battery is not inserted, continuous lighting of the
battery charge indicator indicates that the mains plug is
inserted in the socket and that the battery charger is ready for
operation.
Continuous Lighting of the Red Battery Charge
Indicator
Continuous lighting of the red battery charge
indicator indicates that the temperature of the
battery is not within the allowable charging temperature
range, see section "Technical Data". As soon as the allowable
charging temperature range is reached, the battery charger
automatically switches to rapid charging.
Flashing Red Battery Charge Indicator
A flashing red battery charge indicator
indicates a different malfunction of the
charging procedure, see section "Troubleshooting – Causes
and Corrective Measures".
Meaning of the Indication Elements (AL 1815 CV)
Flashing Battery Charge Indicator
The charging procedure is signalled by a
flashing battery charge indicator .
Continuous Lighting of the Battery Charge
Indicator
Continuous lighting of the battery charge
indicator indicates that the battery is fully
charged or that the temperature of the battery is not within
the allowable charging temperature range, and cannot be
charged for this reason. The battery is charged as soon as the
allowable charging temperature range is reached.
When the battery is not inserted, continuous lighting of the
battery charge indicator indicates that the mains plug is
inserted in the socket and that the battery charger is ready for
operation.
Troubleshooting – Causes and Corrective
Measures
Cause Corrective Measure
Continuous lighting of the battery charge indicator
Continuous lighting of the battery charge indicator
Flashing red battery charge indicator
No charging procedure possible
The battery is not attached Attach battery to charger
(correctly) correctly
Battery contacts Clean the battery contacts
contaminated (e.g. by inserting and
removing the battery several
times) or replace the battery
Battery pack defective Replace the battery
Bosch Power Tools
Cause Corrective Measure
Battery charge indicators or do not light up
Mains plug of battery charger Insert mains plug (fully) into
not plugged in (properly) the socket outlet
Socket outlet, mains cable or Check the mains voltage;
battery charger defective have the battery charger
checked by an authorised
after-sales service agent for
Bosch power tools
Charging Advice
With continuous or several repetitive charging cycles without
interruption, the charger can warm up. This does not indicate
a technical defect of the battery charger.
A significantly reduced working period after charging
indicates that the battery is used and must be replaced.
Assembly
 Before any work on the machine itself (e. g.
maintenance, tool change, etc.) as well as during
transport and storage, remove the battery from the
power tool. There is danger of injury when unintentionally
actuating the On/Off switch with the locking button.
Tool assembly (see figure C+E)
Fit the hedge trimmer head together with the telescopic
handle, tighten them together with the connector 3 by
twisting it. Make sure that both parts are properly fitted.
Attach the harness 8 to the harness loops 7/9 located in the
handling areas. Please notice that the harness has two hooks
that are different in size. Make sure that the bigger hook 16 is
fitted onto the main handle harness loop 9 and the smaller
hook 15 onto the front handle harness loop 7.
Remove the blade cover.
Adjusting the telescopic height (see figure F)
Loosen the telescopic height adjustment joint 5 by rotating,
extend the telescopic tube 4 to the required length and re-
tighten the adjustment joint 5 by twisting.
The telescopic tube 4 can be extended from 2.1 m to 2.60 m
depending on the application and the height of the trimmed
hedge.
Adjusting the pivoting head (see figure H)
Press two pivoting head adjustment buttons 2
simultaneously, adjust the pivoting head to the required
position by moving the hedge trimmer head upwards or
downwards, release the pivoting head adjustment buttons 2
and make sure that the hedge trimmer head is properly
locked.
Pivoting head can be adjusted to 10 different positions.
English | 19
F 016 L81 577 | (28.9.17)