Technical Data Of Jive Escs; Features Of The Jive Escs; Properties; Bec - Kontronik Jive Bedienungsanleitung

capacity batteries sufficient cooling must be
guaranteed.
The ESC can only be used in environments in
which no discharge of static electricity occurs.
Do not extend motor cables or battery cables.
Otherwise compliance with legal rules is not
guaranteed. Extension of cables may result in
damage of the ESC.
For current measurement, a tie meter has to be
used, since an inserted meter can damage the
ESC.
When using a BEC it is necessary to connect a
charged receiver battery with enough capacity in
parallel (see BEC). Otherwise a broken wire,
broken battery, loose of contact or a defect of
one electronic BEC part may result in total loss
of the receiver system. The system has to be
tested on ground before the first flight, to assure
that

BEC

capacity
application.
3

Technical data of JIVE ESCs

JIVE ESCs have a mode programming option.
Each mode configurates in the respective operation
conditions all necessary parameters. Complex
programming of individual parameters is not
necessary. For adjusting single parameters use
ProgCARD I (Order # 9305) or ProgCARD II
(Order # 9306)
.
BEC data for all JIVE ESCs:
BEC Voltage (standard / min / max): 5,6V / 5V–6V
BEC Current (cont../max) : 5A / 15A
Specifiactions
Type
JIVE 60+ LV
JIVE 80+ LV
JIVE 100+ LV
JIVE 60+ HV
JIVE 80+ HV
POWERJIVE 120+ HV
4

Features of the JIVE ESCs

With the JIVE ESC you purchased a high quality
product. High quality plugs (e.g. KONTRONIK
Plugs, order # 9010) as well as low resistance
soldered batteries should be obligatory. Please
contact KONTRONIK service for detailed questions
about special applications of this ESC.
is sufficient for this
Input Constant
Voltage Current
6V-25V 60A
6V-25V 80A
6V-25V 100A
16-50V 60A
16-50V 80A
16-50V 120A
4.1

Properties

Sensorless, no sensor signals from motor are
required
Mode programming
EMF-brake with variable brake rate, can be
disabled
Automatic under
adjustable and detachable. Reducing power,
instead of switching off is possible.
Unlimited part load capability
Analysis of switching-off reason
Adjusting monitored by LED or audio signal
Very sensitive control characteristic, smooth
start up
Sensing and computing of the actual motor data
− self adjusting beat frequency (8-32kHz)
−
dynamic timing
Start protection at power up, blocked motor
protection, over temperature protection, over
current limitation
Digital microprocessor control, therefore no
thermal drift, possible to update
24 months warranty, CE tested,
service, hotline service
Developed and
Germany
4.2 BEC
All JIVE ESCs include a synchronized BEC.
Compared to general BEC-systems the capacity of
the BEC is mostly independent from the input
voltage. This allows the usage of the BEC also at
higher voltages. Also, the BEC features a high
suppression of interference. The BEC-Voltage can
be changed between 5V and 6V (0.2V steps) by
using ProgCARD II.
For safety reasons a four cell NiCd/NiMH
!
battery must be connected to the receiver
in parallel to the BEC.
For BEC voltages exceeding 5.6V a redundant
receiver AC current supply should be connected.
Using this ESC without BEC is possible by pulling
the red receiver cable off the connector or by
ripping this cable.
4.3

Toroidal core

The toroidal core on the receiver cable allows
suppression of interference and must not be
removed from the cable for security reasons.
voltage disconnection,
fast repair
produced in Rottenburg,
15