Herunterladen Inhalt Inhalt Diese Seite drucken
Inhaltsverzeichnis
Verfügbare Sprachen

Verfügbare Sprachen

In the interests of user-safety (Required by safety regulations in some countries) the set should be restored
to its original condition and only parts identical to those specified should be used.
Im lnteresse der Benutzersicherheit (erforderliche Sicherheitsregeln in einigen Ländern) muß das Gerät in seinen
Originalzustand gebracht werden. Außerdem dürfen für die spezifizierten Bauteile nur identische Teile verwendet
werden.
CONTENTS
» NOTE TO SERVICE PERSONNEL ............................ 2
» SPECIFICATIONS ...................................................... 3
» OPERATION MANUAL ............................................... 4
» REMOVING OF MAJOR PARTS ................................ 9
» RESETTING THE LAMP TIMER .............................. 14
» THE OPTICAL UNIT OUTLINE ................................ 15
» ELECTRICAL ADJUSTMENT ................................... 20
» TROUBLE SHOOTING TABLE ................................ 27
» CHASSIS LAYOUT ................................................... 80
and BLOCK DIAGRAM ............................................. 82
» WAVEFORMS ........................................................... 85
» SCHEMATIC DIAGRAM ........................................... 86
Ë ELECTRICAL PARTS ........................................ 137
Ë CABINET AND MECHANICAL PARTS .............. 162
Ë ACCESSORIES PARTS .................................... 166
Ë PACKING PARTS ............................................... 166
» PACKING OF THE SET .......................................... 167
SERVICE MANUAL
SERVICE-ANLEITUNG
LCD PROJECTOR
LCD PROJEKTOR
MODEL
MODELL
Page
» TECHNISCHE DATEN ............................................. 42
» BEDIENUNGSANLEITUNG ..................................... 43
» ENTFERNEN DER HAUPTTEILE ............................ 48
» ÜBERSICHT DER OPTIKEINHEIT .......................... 54
» ELEKTRISCHE EINSTELLUNG ............................... 59
» FEHLERSUCHTABELLE .......................................... 66
» CHASSIS-ANORDNUNG ......................................... 80
» WELLENFORMEN ................................................... 85
» SCHEMATISCHER SCHALTPLAN .......................... 86
» LEITERPLATTENEINHEITEN ................................ 128
» VERPACKEN DES GERÄTS .................................. 167
SHARP CORPORATION
1
XV-ZW60E
INHALT
BETRIEBSSTUNDENZÄHLERS .............................. 53
BRENNPUNKT ......................................................... 55
und BLOCKSCHALTBILD ......................................... 82
SCHALTPLANS ........................................................ 84
Ë ELEKTRISCHE BAUTEILE ................................ 137
Ë ZUBEHÖRTEILE ................................................ 166
Ë VERPACKUNGSTEILE ...................................... 166
XV-ZW60E
S59H3XV-ZW60E
Seite
Inhaltsverzeichnis
loading

Inhaltszusammenfassung für Sharp XV-ZW60E

  • Seite 1: Inhaltsverzeichnis

    XV-ZW60E SERVICE MANUAL SERVICE-ANLEITUNG S59H3XV-ZW60E LCD PROJECTOR LCD PROJEKTOR MODEL XV-ZW60E MODELL In the interests of user-safety (Required by safety regulations in some countries) the set should be restored to its original condition and only parts identical to those specified should be used.
  • Seite 2: Note To Service Personnel

    (Fig. 1). Note: Please obtain a lens cap before servicing a model XV-ZW60E that is received without one. UV-Radiation and Medium Pressure Lamp Precautions LENS CAP 1. Be sure to disconnect the AC plug when replacing the lamp.
  • Seite 3: Specifications

    XV-ZW60E Specifications...
  • Seite 4: Location Of Controls

    XV-ZW60E Location of Controls...
  • Seite 5 XV-ZW60E Operating the Wireless Mouse Remote Control...
  • Seite 6 XV-ZW60E...
  • Seite 7 XV-ZW60E Connection Pin Assignments...
  • Seite 8 XV-ZW60E Dimensions...
  • Seite 9: Removing Of Major Parts

    XV-ZW60E REMOVING OF MAJOR PARTS 1. Removing the Lamp cage unit and Intake cover 1-1. Remove the intake cover. 1-2. Remove the screws and detach the lamp cage cover. 1-3. Remove the three screws off the lamp cage unit. 1-4. Pull out the lamp cage unit.
  • Seite 10 XV-ZW60E 2. Removing the front cabinet 2-1. Remove the four right and left screws from the bottom of the front cabinet. 2-2. Gently press down on the hooks A, B, C and D of the top cabinet to unhook the front cabinet. Detach the front cabinet.
  • Seite 11 XV-ZW60E 4. Removing the left side cabinet 4-1. Remove the eight side screws. 4-2. Remove the three screws off the side cabinet. 4-3. Disconnect the membrane switch connector. 4-4. Pull down and detach the left side cabinet. 4-5. Remove the two screws off the LED PWB assembly.
  • Seite 12 XV-ZW60E 5. Disconnecting the signal and output PWBs 5-1. Remove the three screws off the optical mechanism assembly. 5-2. Remove the two screws off the bottom cabinet. 5-3. Remove the screw off the signal PWB assembly. 5-4. Remove the three screws off the output PWB assembly.
  • Seite 13 XV-ZW60E 6. Removing the power supply and ballast PWBs 6-1. Remove the two screws off the AC/SW Unit on the bottom cabinet. 6-2. Remove the four screws off the power/ballast holder (located behind). 6-3. Disconnect the connectors. 6-4. Take up and away the PWBs.
  • Seite 14: Resetting The Lamp Timer

    XV-ZW60E RESETTING THE LAMP TIMER The unit is designed to keep its power off when the lamp has been used for 1400 and 1500 hours. This is to protect the lamp fixture. Replace the lamp with new one and take the following resetting procedure.
  • Seite 15: The Optical Unit Outline

    XV-ZW60E THE OPTICAL UNIT OUTLINE Layout of the optical system Note: Layout for positioning the optical system. Projection Lens Polarizing film Incident polarizing plate B Pre-polarizing film Incident polarizing plate R Pre-polarizing plate Dichroic coating Dichroic coating (B transmission) (R transmission)
  • Seite 16: Covergence And Focus Adjustment

    XV-ZW60E CONVERGENCE AND FOCUS ADJUSTMENT » Start the convergence and focus adjustments with the top cabinet and the signal shield removed but the power on. Use the remote control to adjust the image. Take the following procedures. 1. Focusing the projection lens (A) Replacing all the 3 LCD panels 1.
  • Seite 17: Top View

    XV-ZW60E Notes : 1 The eccentric cam is used for convergence adjustment. This means that the cam’s turning and the linear movement are not always uniform. 2 This model is not equipped with the LCD image adjustment mechanism. This is because the dichroic prism is used for image formation.
  • Seite 18 XV-ZW60E Convergence and Focus Adjustments at a Glance Adjustment directions Adjustment Direction Definition Direction of LCD panel X direction LCD right and left Convergence Y direction LCD top and bottom θZ direction Rotation around Z axis LCD turning axis Z direction LCD optical axis θX direction...
  • Seite 19 XV-ZW60E Replacing the LCDs With the top cabinet removed (1) Remove three screws off the output shield. (2) Disconnect the LCD flat cable from the output PWB connector. (3) Remove the lock screws "b" and "c". Detach the R/B adjusting plate or the G adjusting plate together with the LCD panel.
  • Seite 20: Electrical Adjustment

    XV-ZW60E ELECTRICAL ADJUSTMENT NOTE : The settings have been factory-adjusted to their best points. If any of them gets out of spec or after any relevant part has been replaced, make the related adjustment. Adjustment Conditions Adjustment Method Adjustment Position •...
  • Seite 21 XV-ZW60E Adjustment Conditions Adjustment Method Adjustment Position • Using the ' and " keys, adjust the PAL Colour 1. Receive the PAL colour bar signal. (DAC) difference between the 100% white 2. Connect the oscilloscope between pin (1) level and the primary red level to (RRR1) of P3004 and GND.
  • Seite 22 XV-ZW60E Adjustment Conditions Adjustment Method Adjustment Position • Using the ' and " keys, adjust the Component 1. Receive the NTSC 10-step signal via the Brightness component input. data so that the pedestal level signal (DAC) becomes bit-less (noise) in green.
  • Seite 23 XV-ZW60E Adjustment Conditions Adjustment Method Adjustment Position • Using the ' and " keys, adjust the 1. Receive the SMPTE pattern signal (VGA Brightness or SVGA) via the computer input. data so that the 0% black level signal (DAC) becomes bit-less (noise) in green.
  • Seite 24 XV-ZW60E Adjustment Conditions Adjustment Method Adjustment Position P-Y-DLY 1. Press S2001 to call up the ADJ IN mode • Make sure that the setting is 0. (DAC) and select the following subject. Group: VIDEO 2 Subject: P-Y-DLY 1. Press S2001 to call up the ADJ IN mode •...
  • Seite 25 XV-ZW60E Adjustment Conditions Adjustment Method Adjustment Position PSIG 1. R: Connect the oscilloscope between • Make sure that the setting is 46. (DAC) TP1031(R) and GND. G: Connect the oscilloscope between TP1033(G) and GND. B: Connect the oscilloscope between TP1034(B) and GND.
  • Seite 26 XV-ZW60E Adjustment Conditions Adjustment Method Adjustment Position Sawtooth Wave 1. Receive the NTSC monoscope pattern • Adjust R1418 until there is least Correction Level signal via the video input. Call up the horizontal color irregularity visible on FULL mode. the screen.
  • Seite 27: Trouble Shooting Table

    XV-ZW60E TROUBLE SHOOTING TABLE Checking the PWB performance RGB input trouble Video system trouble Component system trouble Go to "Checking the component Feed test pattern signal from PC Go to "Checking video system" system" Is specified cable connected between Use specified cable...
  • Seite 28 XV-ZW60E TROUBLE SHOOTING TABLE (Coutinued) Checking the R signal line of signal processing PWB Is there signal at pin (7) of IC3501 Check pin (1) line of connector TN Is there output at pin (40) of Do voltages at pins (5), (18) and (19)
  • Seite 29 XV-ZW60E TROUBLE SHOOTING TABLE (Coutinued) Checking the G signal line of signal processing PWB Is there signal at pin (11) of IC3501 Check pin (3) line of connector TN Is there output at pin (35) of IC3501 Do voltages at pins (6), (18) and (19)
  • Seite 30 XV-ZW60E TROUBLE SHOOTING TABLE (Coutinued) Checking the B signal line of signal processing PWB Is there signal at pin (17) of IC3501 Check pin (5) line of connector TN Is there output at pin (30) of IC3501 Do voltages at pins (7), (18) and (19)
  • Seite 31 XV-ZW60E TROUBLE SHOOTING TABLE (Coutinued) Checking the R signal line of output PWB Are input at pin (13) of IC1010 as Check pin (47) line of connector specified? SC1001 Are output at pin (25) of IC1010 as IC1010 or nearby circuit in trouble...
  • Seite 32 XV-ZW60E TROUBLE SHOOTING TABLE (Coutinued) Checking the G signal line of output PWB Are input at pin (10) of IC1010 as Check pin (50) line of connector specified? SC1001 Are output at pin (30) of IC1010 as IC1010 or nearby circuit in trouble...
  • Seite 33 XV-ZW60E TROUBLE SHOOTING TABLE (Coutinued) Checking the B signal line of output PWB Are input at pin (10) of IC1010 as Check pin (51) line of connector specified? SC1001 Are output at pin (30) of IC1010 as IC1010 or nearby circuit in trouble...
  • Seite 34 XV-ZW60E TROUBLE SHOOTING TABLE (Coutinued) Checking the video system No picture Is lamp on? Lamp fails or Power unit in trouble Is voltage applied to connetor EA? Power unit in trouble Are there signal input at pin (1) of Connector J402 or input circuit in...
  • Seite 35 XV-ZW60E TROUBLE SHOOTING TABLE (Coutinued) Checking the compornent system No picture Are there signals output at pins (3), (5) Connector J405, IC410 or nearby circuit and (6) of IC410? ( in case of video1) in trouble Are there signal input at pins (33) thru...
  • Seite 36 XV-ZW60E TROUBLE SHOOTING TABLE (Coutinued) Are there CLK signals at pins (26), (27) IC4013 or nearby circuit in trouble and (28) of IC4016? IC4006, Q4011, Q4012 or nearby circuit in trouble Checking the MMC circuit Check X3004(80MHz), Are there H sync signal output at pin (54)
  • Seite 37 XV-ZW60E TROUBLE SHOOTING TABLE (Coutinued) No colour or unusual tint with NTSC signal Check IC2001, IC3016 and nearby Is colour mode judged propery? circuit Is there chroma signal input at pin Check pin (50) line of connector SC1001 (20) of IC3016?
  • Seite 38 XV-ZW60E TROUBLE SHOOTING TABLE (Coutinued) Checking the PLL-1 circuit Are there signal input at pin (7) of Go to "Checking synchronization-1" IC3503? Are there Bus signal input at pins (3) and IC2001 or nearby circuit in trouble (4) of IC3503?
  • Seite 39 XV-ZW60E TROUBLE SHOOTING TABLE (Coutinued) Checking the remote control circuit Press the MENU key. Are there signal outputs at pins (9) and (10) of connector SC1001? Remote control receiver or its nearby circuit in trouble. IC2001, IC2005, IC2009 or nearby circuit in trouble.
  • Seite 40 XV-ZW60E TROUBLE SHOOTING TABLE (Coutinued) No sound Are there audio signal inputs at pins (2) and (23) of IC1003? IC1004, IC1005, IC401 or nearby circuit in trouble. Are there audio signal inputs at pins (1) and (9) of IC7301? IC5301 or nearby circuit in trouble.
  • Seite 41: Hinweise Für Das Wartungspersonal

    Gehäuse ist nicht zulässig. werden, um die Bestrahlung von Augen und Haut zu vermeiden (Abb. 1). Hinweis: Besorgen Sie sich einen Objektivdeckel, bevor Sie Arbeiten an einem Modelle XV-ZW60E durchführen, das keinen Objektivdeckel aufweist. Objectivdeckel Zur Beachtung bei UV-Strahlung und Mitteldruck-Lampen 1.
  • Seite 42: Technische Daten

    XV-ZW60E Technische Daten...
  • Seite 43: Lage Der Bedienelemente

    XV-ZW60E Lage der Bedienelemente...
  • Seite 44: Betried Mit Der Drahtlosen Maus-Fernbedienung

    XV-ZW60E Betried mit der drahtlosen Maus-Fernbedienung...
  • Seite 45 XV-ZW60E...
  • Seite 46: Pinbelegung

    XV-ZW60E Pinbelegung...
  • Seite 47: Abmessungen

    XV-ZW60E Abmessungen...
  • Seite 48: Entfernen Der Hauptteile

    XV-ZW60E ENTFERNEN DER HAUPTTEILE 1. Entfernen der Lampenkäfigeinheit und der Lufteinlaßabdeckung 1-1. Die Lufteinlaßabdeckung abnehmen. 1-2. Die Schrauben losdrehen und die Lampenkäfigabdeckung abnehmen. 1-3. Die drei Schrauben von der Lampenkäfigeinheit losdrehen. 1-4. Die Lampenkäfigeinheit abziehen. Hinweise: » Vor dem Auswechseln den Betriebstaste der Projektors ausschalten, darauf acten, daß das Kühlgebläse zum Stillstand kommt, und den Netzstecker herausziehen.
  • Seite 49 XV-ZW60E 2. Entfernen des vorderen Gehäuseteils 2-1. Die vier rechten und linken Schrauben von der Unterseite des vorderen Gehäuseteils losdrehen. 2-2. Die Haken des oberen Gehäuseteils A, B, C, und D vorsichtig nach unten drücken, um das vordere Gehäuseteil zu lösen. Nun das vordere Gehäuseteil abnehmen.
  • Seite 50 XV-ZW60E 4. Entfernen des linken Seitenteils 4-1. Die acht seitlichen Schrauben losdrehen. 4-2. Die drei Schrauben vom seitlichen Gehäuseteil losdrehen. 4-3. Den Membranschalter-Steckverbinder abziehen. 4-4. Das linke Seitenteil nach unten ziehen und entfernen. 4-5. Die beiden Schrauben von der Leuchtdioden-Platineneinheit losdrehen.
  • Seite 51 XV-ZW60E 5. Abtrennen der Signal- und Ausgangsplatine 5-1. Die drei Schrauben von der optischen Mechanismuseinheit losdrehen. 5-2. Die beiden Schrauben vom unteren Gehäuseteil losdrehen. 5-3. Die Schraube von der Signalplatineneinheit losdrehen. 5-4. Die drei Schrauben von der Ausgangsplatine losdrehen. 5-5. Die Steckverbinder von den Signal- und Ausgangsplatineneinheiten abziehen.
  • Seite 52 XV-ZW60E 6. Entfernen der Netz/Ballast-Platine 6-1. Die beiden Schrauben von der Netzschalter-einheit am unteren Gehäuseteil losdrehen. 6-2. Die vier Schrauben vom Netz/Ballast-Halter losdrehen (an der Rückseite). 6-3. Die Steckverbinder abziehen. 6-4. Die Platinen entfernen. Netz-/Ballasteinheit Netzschalter-einheit...
  • Seite 53: Nullstellung Des Lampen-Betriebsstundenzählers

    XV-ZW60E NULLSTELLUNG DES LAMPEN-BETRIEBSSTUNDENZÄHLERS Dieses Gerät dient dazu, um die Stromzufuhr zu unterbrechen, wenn die Lampe für 1400 und 1500 Stunden betrieben wurde. Dies dient zum Schutz des Beleuchtungskörpers. Num die Lampe gegen eine neue auszuwechseln und das folgende Rückstellungsverfahren ausführen.
  • Seite 54: Übersicht Der Optikeinheit

    XV-ZW60E ÜBERSICHT DER OPTIKEINHEIT Übersicht des optischen Systems Hinweis: Anordnung der Bauteile im optischen System Projektionsobjektiv Polarisationsbeschichtung Polarisatorplatte B für einfallendes Licht Vorpolarisationsbeschichtung Polarisatorplatte R Vorpolarisationsplatte für einfallendes Licht Zweifarbige Beschichtung Zweifarbige Beschichtung (B-Übertragung) (R-Übertragung) R-LCD B-LCD Zweifarbiges Kreuzprisma Markierung...
  • Seite 55: Einstellung Von Konvergenz Und Brennpunkt

    XV-ZW60E EINSTELLUNG VON KONVERGENZ UND BRENNPUNKT » » » » » Die Einstellarbeiten für die Konvergenz und die Brennpunkteinstellung bei entferntem oberem Gehäuseteil und Signalschild vornehmen. Das Gerät muß dabei jedoch eingeschaltet sein. Zur Bildeinstellung ist die Fernbedienungseinheit zu verwenden.
  • Seite 56 XV-ZW60E (B) Konvergenzeinstellung » Für diese Einstellung ist ein Kreuzschraffier-Muster zu benutzen. Die Einstellung ist ausschließlich für die G-Farbe und die zutreffende Farbe. (1) Die Konvergenz-Sicherungsschraube “d” lockern. (2) Die B-LCD-Anzeige in den Richtungen X, Y und θZ einstellen, wobei die Leinwandmitte der G-LCD- Anzeige als Referenz herangezogen werden muß.
  • Seite 57 XV-ZW60E Konvergenz- und Brennpunkteinstellungen auf einen Blick Einstellrichtungen Einstellung Richtung Definition Richtung der LCD-Anzeige X-Richtung LCD rechts und links Konvergenz Y-Richtung LCD oben und unten θZ-Richtung Drehung um die Z-Achse LCD-Drehachse Z-Richtung LCD, optische Achse θX-Richtung Drehung um die X-Achse...
  • Seite 58: Draufsicht

    XV-ZW60E Auswechseln der LCDs Bei entferntem oberen Gehäuseteil: (1) Die Ausgangsabdeckung entfernen. (2) Das LCD-Flachkabel vom Platinen-Ausgangsstecker abklemmen. (3) Die Sicherungsschrauben “b” und “c” losdrehen. Die R/B-Einstellplatte abnehmen, oder die G-Einstellplatte zusammen mit der LCD-Anzeige entfernen. (4) Die LCD-Anzeige von der Einstellplatte trennen.
  • Seite 59: Elektrische Einstellung

    XV-ZW60E ELEKTRISCHE EINSTELLUNG HINWEIS: Sämtliche Einstellungen wurden bereits werkseitig optimal ausgeführt. Wenn nach dem Auswechseln von Bauteilen bestimmte Werte nicht mehr den Sollwerten entsprechen, sind die entsprechenden Einstellungen vorzunehmen. Einstellposition Einstellbedingungen Einstellverfahren • Mit den Tasten ' und " die Video-Kontrast 1.
  • Seite 60 XV-ZW60E Einstellposition Einstellbedingungen Einstellverfahren • Mit den Tasten ' und " die Differenz PAL-Farbe 1. Das PAL-Farbbalkensignal empfangen. (DAC) 2. Das Oszilloskop zwischen Stift (1) zwischen dem 100%-Weißpegel und (RRR1) von P3004 und GND dem Primärrotpegel auf 0,2 ± 0,05 anschließen.
  • Seite 61 XV-ZW60E Einstellposition Einstellbedingungen Einstellverfahren • Mit den Tasten ' und " die Daten Komponenten- 1. Das NTSC 10-Stufensignal durch den Helligkeit Komponenteneingang empfangen. so einstellen, daß das Austastsignal (DAC) 2. Das Oszilloskop zwischen Stift (6) für Grün "bitlos" (Störung) wird.
  • Seite 62 XV-ZW60E Einstellposition Einstellbedingungen Einstellverfahren • Mit den Tasten ' und " die Daten RGB-Helligkeit 1. Das SMPTE-Mustersignal (VGA oder (DAC) SVGA) durch den Computereingang so einstellen, daß das 0%- empfangen. Schwarzsignal für Grün "bitlos" 2. Das Oszilloskop zwischen Stift (2) (Störung) wird.
  • Seite 63: Die R-Gain-, G-Gain- Und B-Gain

    XV-ZW60E Einstellposition Einstellbedingungen Einstellverfahren P-Y-Verzögerung 1. S2001 drücken, um den ADJ IN-Modus • Sicherstellen, daß der Einstellwert 0 (DAC) abzurufen, und die folgende Wahl ist. treffen. Gruppe : VIDEO 2 Gegenstand : P-Y-DLY Verzögerung 1. S2001 drücken, um den ADJ IN-Modus •...
  • Seite 64 XV-ZW60E Einstellposition Einstellbedingungen Einstellverfahren P-Signal 1. R: Das Oszilloskop zwischen • Sicherstellen, daß der Einstellwert (DAC) TP1031(R) und GND anschließen. 46 ist. G: Das Oszilloskop zwischen TP1033(G) und GND anschließen. B: Das Oszilloskop zwischen TP1034(B) und GND anschließen. 2. S2001 drücken, um den ADJ IN-Modus abzurufen, und die folgende Wahl treffen.
  • Seite 65 XV-ZW60E Einstellposition Einstellbedingungen Einstellverfahren Sägezahnwellen- 1. Das NTSC-Monoskopmustersignal • R1418 so einstellen, daß die Korrekturpegel durch den Videoeingang empfangen. horizontale Farbenungleichheit auf Den FULL-Modus wählen. dem Bildschirm minimisiert wird. 2. Die Gummilinse auf die WIDE-Stellung • Die Gummilinse von der WIDE- auf einstellen, so daß...
  • Seite 66: Fehlersuchtabelle

    XV-ZW60E FEHLERSUCHTABELLE Überprüfung der Platinenleistung Gestörtes Videosystem Gestörtes Komponentensystem Gestörte RGB-Eingabe Zum Abschnitt "Überprüfung des Zum Abschnitt "Überprüfung des Ein Mustersignal vom PC zuführen. Videosystems" weitergehen. Komponentensystems" weitergehen. Nein Wurde zwischen PC und Projektor das Das spezifizierte Kabel verwenden. Fernbedienungskabel defekt...
  • Seite 67 XV-ZW60E FEHLERSUCHTABELLE (Fortsetzung) Überprüfung der R-Signalleitung von der Signalprozeß-Platine Nein Das Stift (1) des TN-Anschlusses Liegt ein Signal am Stift (7) von überprüfen IC3501 an? Nein Nein Ändern sich die Spannungen an den Liegt ein Ausgangssignal am Stift (40) IC3502, IC2001 oder peripherer Stiften (5), (18) und (19) von IC3502? von IC3501 ordnungsgemäß...
  • Seite 68 XV-ZW60E FEHLERSUCHTABELLE (Fortsetzung) Überprüfung der G-Signalleitung von der Signalprozeß-Platine Nein Liegt ein Signal am Stift (11) von Das Stift (3) des TN-Anschlusses überprüfen IC3501 an? Nein Nein Liegt ein Ausgangssignal am Stift (35) IC3502, IC2001 oder peripherer Ändern sich die Spannungen an den von IC3501 ordnungsgemäß...
  • Seite 69 XV-ZW60E FEHLERSUCHTABELLE (Fortsetzung) Überprüfung der B-Signalleitung von der Signalprozeß-Platine Nein Liegt ein Signal am Stift (17) von Das Stift (5) des TN-Anschlusses überprüfen IC3501 an? Nein Nein Liegt ein Ausgangssignal am Stift (30) Ändern sich die Spannungen an den IC3502, IC2001 oder peripherer von IC3501 ordnungsgemäß...
  • Seite 70 XV-ZW60E FEHLERSUCHTABELLE (Fortsetzung) Überprüfung der R-Signalleitung von der Ausgangsplatine Nein Ist das Eingangssignal am Stift (13) von Das Stift (47) des SC1001- IC1010 ordnungsgemäß? Anschlusses überprüfen. Nein Liegt ein Ausgangssignal am Stift (25) IC1010 oder peripherer Schaltkreis von IC1010 ordnungsgemäß an? defekt.
  • Seite 71 XV-ZW60E FEHLERSUCHTABELLE (Fortsetzung) Überprüfung der G-Signalleitung von der Ausgangsplatine Nein Ist das Eingangssignal am Stift (10) von Das Stift (50) des SC1001- IC1010 ordnungsgemäß? Anschlusses überprüfen. Nein Liegt ein Ausgangssignal am Stift (30) IC1010 oder peripherer Schaltkreis von IC1010 ordnungsgemäß an? defekt.
  • Seite 72 XV-ZW60E FEHLERSUCHTABELLE (Fortsetzung) Überprüfung der B-Signalleitung von der Ausgangsplatine Nein Ist das Eingangssignal am Stift (10) von Das Stift (51) des SC1001- IC1010 ordnungsgemäß? Anschlusses überprüfen. Nein Liegt ein Ausgangssignal am Stift (30) IC1010 oder peripherer Schaltkreis von IC1010 ordnungsgemäß an? defekt.
  • Seite 73 XV-ZW60E FEHLERSUCHTABELLE (Fortsetzung) Überprüfung des Videosystems Kein Bild Nein Leuchtet die Lampe auf? Lampe oder Netzschaltkreis defekt. Nein Wird eine Spannung zum EA-Anschluß Netzschaltkreis defekt. angelegt? Nein Liegt ein Eingangssignal am Stift (1) J402-Anschluß oder des P3001-Ansclusses an? Eingangsschaltkreis defekt.
  • Seite 74 XV-ZW60E FEHLERSUCHTABELLE (Fortsetzung) Überprüfung des Komponentensystems Kein Bild Nein Liegen Ausgangssignale an den Stiften J405-Anschluß, IC410 oder peripherer (3), (5) und (6) von IC410 an? (bei Schaltkreis defekt. Video 1) Nein Q404, Q405, Q408, Q412, Q413, Liegen Eingangssignale an den Stiften...
  • Seite 75 XV-ZW60E FEHLERSUCHTABELLE (Fortsetzung) Nein Liegen die CLK-Signale an den Stiften IC4013 oder peripherer Schaltkreis (26), (27) und (28) von IC4016 an? defekt. IC4006, Q4011, Q4012 oder peripherer Schaltkreis defekt. Überprüfung des MMC-Schaltkreises Nein X3004 (80MHz), IC4013 (40MHz) und Liegt das Hsync-Ausgangssignal am periphere Schaltkreise überprüfen.
  • Seite 76 XV-ZW60E FEHLERSUCHTABELLE (Fortsetzung) Keine Farbe oder ungewöhnlicher Farbton mit NTSC-Signal Nein Wurde der Farbmodus korrekt IC2001, IC3016 und peripheren beurteilt? Schaltkreis überprüfen. Nein Das Stift (50) des SC1001- Liegt das Chroma-Eingangssignal Anschlusses überprüfen. am Stift (20) von IC3016 an? Nein...
  • Seite 77 XV-ZW60E FEHLERSUCHTABELLE (Fortsetzung) Überprüfung des PLL-1-Schaltkreises Nein Zum Abschnitt "Überprüfung der Liegt ein Eingangssignal am Stift (7) Synchronisation 1" weitergehen. von IC3503 an? Nein IC2001 oder peripherer Schaltkreis Liegen die Bus-Eingangssignale an den defekt. Stiften (3) und (4) von IC3503 an? IC3503 oder peripherer Schaltkreis defekt.
  • Seite 78 XV-ZW60E FEHLERSUCHTABELLE (Fortsetzung) Überprüfung des Fernbedienungs-Schaltkreises Nein Die MENU-Taste drücken. Liegen Ausgangssignale an den Stiften (9) und (10) des SC1001-Anschlusses Fernbedienungsempfänger oder peripherer Schaltkreis defekt. IC2001, IC2005, IC2009 oder peripherer Schaltkreis defekt. Die Lampe leuchtet nicht Die Lampe durch eine neue Lampe defekt.
  • Seite 79 XV-ZW60E FEHLERSUCHTABELLE (Fortsetzung) Kein Ton Nein Liegen Audio-Eingangssignale an den Stiften (2) und (23) von IC1003 IC1004, IC1005, IC401 oder peripherer Schaltkreis defekt. Nein Liegen Audio-Eingangssignale an den Stiften (1) und (9) von IC7301 IC5301 oder peripherer Schaltkreis defekt. Nein...
  • Seite 80: Chassis Layout

    XV-ZW60E CHASSIS LAYOUT / CHASSIS-ANORDNUNG OUTPUT UNIT POWER/BALLAST UNIT DUNTK9756DE02 CDENC0276CE01 INPUT UNIT AC-SW UNIT DUNTK9757DE02 RUNTK0652CEZZ...
  • Seite 81 XV-ZW60E UT UNIT 9756DE02 LED UNIT DUNTK9382DE11 INFRARED R/C RECEIVER UNIT DUNTK9875DE01 SIGNAL UNIT DUNTK9874DE01...
  • Seite 82: Overall Wiring Diagram And Block Diagram

    XV-ZW60E OVERALL WIRING DIAGRAM and BLOCK DIAGRAM / GESAMTSCHALTPLAN-und BLOCKSCHALTBILD AC-SW UNIT SIGNAL UNIT R/C UNIT MEMBRANE SW...
  • Seite 83 XV-ZW60E SW UNIT POWER/BALLAST UNIT OUTPUT UNIT G LCD LED UNIT RANE SW...
  • Seite 84: Description Of Schematic Diagram

    XV-ZW60E DESCRIPTION OF SCHEMATIC BESCHREIBUNG DES DIAGRAM SCHEMATISCHEN SCHALTPLANS VOLTAGE MEASUREMENT CONDITION: SPANNUNGSMESSUNGEN: 1. Spannungen an den Prüfpunkten werden bei einer 1. Voltages at test points are measured at the supply Netzspannung von 230V gemessen, Signale werden voltage of AC 230V. Signals are fed by a colour bar für die Wartung mit einem Farbbalken-Signal...
  • Seite 85: Waveforms

    XV-ZW60E WAVEFORMS WELLENFORMEN P3004 pin 2 (GGG1) P3004 pin 1 (RRR1) P3004 pin 3 (BBB1) P3004 pin 6 (GGG2) P3004 pin 5 (RRR2) H : 10µs/div H : 10µs/div H : 10µs/div H : 10µs/div H : 10µs/div V : 0.5v/div V : 0.5v/div...
  • Seite 86: Ë Signal Unit-1/9 / Signaleinheit-1

    XV-ZW60E Ë SIGNAL UNIT-1/9 / SIGNALEINHEIT-1/9...
  • Seite 87 XV-ZW60E...
  • Seite 88: Ë Signal Unit-2/9 / Signaleinheit-2

    XV-ZW60E Ë SIGNAL UNIT-2/9 / SIGNALEINHEIT-2/9...
  • Seite 89 XV-ZW60E...
  • Seite 90: Ë Signal Unit-3/9 / Signaleinheit-3

    XV-ZW60E Ë SIGNAL UNIT-3/9 / SIGNALEINHEIT-3/9...
  • Seite 91 XV-ZW60E...
  • Seite 92: Ë Signal Unit-4/9 / Signaleinheit-4

    XV-ZW60E Ë SIGNAL UNIT-4/9 / SIGNALEINHEIT-4/9...
  • Seite 93 XV-ZW60E...
  • Seite 94: Ë Signal Unit-5/9 / Signaleinheit-5

    XV-ZW60E Ë SIGNAL UNIT-5/9 / SIGNALEINHEIT-5/9...
  • Seite 95 XV-ZW60E...
  • Seite 96: Ë Signal Unit-6/9 / Signaleinheit-6

    XV-ZW60E Ë SIGNAL UNIT-6/9 / SIGNALEINHEIT-6/9...
  • Seite 97 XV-ZW60E...
  • Seite 98: Ë Signal Unit-7/9 / Signaleinheit-7

    XV-ZW60E Ë SIGNAL UNIT-7/9 / SIGNALEINHEIT-7/9...
  • Seite 99 XV-ZW60E...
  • Seite 100: Ë Signal Unit-8/9 / Signaleinheit-8

    XV-ZW60E Ë SIGNAL UNIT-8/9 / SIGNALEINHEIT-8/9...
  • Seite 101 XV-ZW60E...
  • Seite 102: Ë Signal Unit-9/9 / Signaleinheit-9

    XV-ZW60E Ë SIGNAL UNIT-9/9 / SIGNALEINHEIT-9/9...
  • Seite 103 XV-ZW60E...
  • Seite 104: Ë Output Unit-1/6 / Ausgabeeinheit-1

    XV-ZW60E Ë OUTPUT UNIT-1/6 / AUSGABEEINHEIT-1/6...
  • Seite 105 XV-ZW60E...
  • Seite 106: Ë Output Unit-2/6 / Ausgabeeinheit-2

    XV-ZW60E Ë OUTPUT UNIT-2/6 / AUSGABEEINHEIT-2/6...
  • Seite 107 XV-ZW60E...
  • Seite 108: Ë Output Unit-3/6 / Ausgabeeinheit-3

    XV-ZW60E Ë OUTPUT UNIT-3/6 / AUSGABEEINHEIT-3/6...
  • Seite 109 XV-ZW60E...
  • Seite 110: Ë Output Unit-4/6 / Ausgabeeinheit-4

    XV-ZW60E Ë OUTPUT UNIT-4/6 / AUSGABEEINHEIT-4/6...
  • Seite 111 XV-ZW60E...
  • Seite 112: Ë Output Unit-5/6 / Ausgabeeinheit-5

    XV-ZW60E Ë OUTPUT UNIT-5/6 / AUSGABEEINHEIT-5/6...
  • Seite 113 XV-ZW60E...
  • Seite 114: Ë Output Unit-6/6 / Ausgabeeinheit-6

    XV-ZW60E Ë OUTPUT UNIT-6/6 / AUSGABEEINHEIT-6/6...
  • Seite 115 XV-ZW60E...
  • Seite 116 XV-ZW60E XV-ZW60E Ë LED and INFRARED R/C RECEIVER UNIT / LED und INFRAROTEMPFÄNGEREINHEIT...
  • Seite 117 XV-ZW60E XV-ZW60E Ë INPUT UNIT-1/2 / EINGANGSEINHEIT-1/2...
  • Seite 118 XV-ZW60E XV-ZW60E Ë INPUT UNIT-2/2 / EINGANGSEINHEIT-2/2...
  • Seite 119 XV-ZW60E XV-ZW60E Ë POWER-1/2 and AC-SW UNIT / NETZEINHEIT-1/2 und NETZSCHALTEREINHEIT (POWER) (AC-SW)
  • Seite 120 XV-ZW60E XV-ZW60E Ë POWER UNIT-2/2 / NETZEINHEIT-2/2...
  • Seite 121 XV-ZW60E Ë BALLAST UNIT / BALLASTEINHEIT...
  • Seite 122: Printed Wiring Board Assemblies Leiterplatteneinheiten

    XV-ZW60E PRINTED WIRING BOARD ASSEMBLIES LEITERPLATTENEINHEITEN Signal Unit (Wiring Side) Signaleinheit (Leiterbahnseite)
  • Seite 123 XV-ZW60E Signal Unit (Component Side) Signaleinheit (Bestückungsseite)
  • Seite 124 XV-ZW60E Output Unit (Wiring Side) Ausgabeeinheit (Leiterbahnseite)
  • Seite 125 XV-ZW60E Output Unit (Component Side) Ausgabeeinheit (Bestückungsseite)
  • Seite 126 XV-ZW60E Input Unit (Wiring Side) Eingangseinheit (Leiterbahnseite) Input Unit (Component Side) Eingangseinheit (Bestückungsseit)
  • Seite 127 XV-ZW60E AC-SW Unit (Wiring Side) Netzschaltereinheit (Leiterbahnseite) Infrared R/C Receiver Unit Infrared R/C Receiver Unit (Wiring Side) (Component Side) Infrarodferbediengseinheit Infrarodferbediengseinheit (Leiterbahnseite) (Bestückungsseite)
  • Seite 128: Printed Wiring Board Assemblies

    XV-ZW60E Power/Ballast Unit-2 (Wiring Side) Netz-/Ballasteinheit-2 (Leiterbahnseite) Power/Ballast Unit-1 (Wiring Side) Netz-/Ballasteinheit-1 (Leiterbahnseite)
  • Seite 129 XV-ZW60E Power/Ballast Unit-2 (Component Side) Netz-/Ballasteinheit-2 (Bestückungsseite) Power/Ballast Unit-1 (Component Side) Netz-/Ballasteinheit-1 (Bestückungsseite)
  • Seite 130 XV-ZW60E LED Unit (Wiring Side) LED-Einheit (Leiterbahnseite) LED Unit (Component Side) LED-Einheit (Bestückungsseite)
  • Seite 131: Parts List

    XV-ZW60E Ref. No. Part No. Description Code Ref. No. Part No. Description Code PARTS LIST ERSATZTEILLISTE AUSTAUSCH VON TEILEN PARTS REPLACEMENT Ersatzteile, die besondere Sicherheitseigenschften haben, sind in Replacement parts which have these special safety characteristics dieser Anleitung markiert. Elektrische Komponenten mit solchen identified in this manual: electrical components having such fea- Eigenshaften sind in den Ersatzteil durch "å"...
  • Seite 132 XV-ZW60E Ref. No. Part No. Description Code Ref. No. Part No. Description Code DUNTK9874DE01 Q4008 VS2SC2412KQ-1 J 2SC2412KQ Q4009 VS2SC2412KQ-1 J 2SC2412KQ SIGNAL UNIT (Continued) Q4010 VS2SC2412KQ-1 J 2SC2412KQ Q4011 VS2SC2412KQ-1 J 2SC2412KQ IC4013 RH-iX1946CEZZ J 74F74SJ Q4012 VS2SA1037KQ-1 J 2SA1037KQ...
  • Seite 133 XV-ZW60E Ref. No. Part No. Description Code Ref. No. Part No. Description Code DUNTK9874DE01 C3151 VCFRED1HM332J J 3300p 50V Mylar C3152 VCCCCY1HH180J J 18p Ceramic SIGNAL UNIT (Continued) C3153 VCKYCY1HB103K J 0.01 Ceramic C3154 VCKYCY1EF104Z J 0.1 Ceramic C879 VCE9PF1CW106M J 10 Elect.(N.P)
  • Seite 134 XV-ZW60E Ref. No. Part No. Description Code Ref. No. Part No. Description Code DUNTK9874DE01 C3602 VCCCCY1HH150J J 15p Ceramic C3603 VCCCCY1HH150J J 15p Ceramic SIGNAL UNIT (Continued) C3604 VCKYCY1CF104Z J 0.1 Ceramic C3605 VCKYCY1CF104Z J 0.1 Ceramic C3515 VCKYCY1CF104Z J 0.1 Ceramic C3606 VCEAPF1HW105M J 1.0...
  • Seite 135 XV-ZW60E Ref. No. Part No. Description Code Ref. No. Part No. Description Code DUNTK9874DE01 C5026 VCEAPF0JW476M J 47 6.3V Electrolytic C5027 VCKYCY1EF104Z J 0.1 Ceramic SIGNAL UNIT (Continued) C5029 VCKYCY1HB103K J 0.01 Ceramic C5030 VCCCCY1HH5R0C J 5.0p Ceramic C4065 VCEAPF0JW226M J 22 6.3V Electrolytic...
  • Seite 136 XV-ZW60E Ref. No. Part No. Description Code Ref. No. Part No. Description Code DUNTK9874DE01 R3259 VRS-CY1JF122J J 1.2k 1/16W Metal Oxide R3260 VRS-CY1JF682J J 6.8k 1/16W Metal Oxide SIGNAL UNIT (Continued) R3261 VRS-CY1JF392J J 3.9k 1/16W Metal Oxide R3262 VRS-CY1JF222J J 2.2k 1/16W Metal Oxide...
  • Seite 137: Parts List

    XV-ZW60E Ref. No. Part No. Description Code Ref. No. Part No. Description Code DUNTK9874DE01 R3587 VRS-CB1JF560J J 56 1/16W Metal Oxide R3588 VRS-CB1JF560J J 56 1/16W Metal Oxide SIGNAL UNIT (Continued) R3589 VRS-CB1JF560J J 56 1/16W Metal Oxide R3590 VRS-CB1JF560J...
  • Seite 138 XV-ZW60E Ref. No. Part No. Description Code Ref. No. Part No. Description Code DUNTK9874DE01 R3840 VRS-TV1JD100J J 10 1/16W Metal Oxide R3841 VRS-TV1JD100J J 10 1/16W Metal Oxide SIGNAL UNIT (Continued) R3842 VRS-TX2HF100J J 10 1/2W Metal Oxide R4001 VRS-CY1JF103J...
  • Seite 139 XV-ZW60E Ref. No. Part No. Description Code Ref. No. Part No. Description Code DUNTK9874DE01 R4204 VRS-CY1JF103J J 10k 1/16W Metal Oxide R4205 VRS-CY1JF103J J 10k 1/16W Metal Oxide SIGNAL UNIT (Continued) R4206 VRS-CY1JF103J J 10k 1/16W Metal Oxide R4207 VRS-CY1JF103J...
  • Seite 140 XV-ZW60E Ref. No. Part No. Description Code Ref. No. Part No. Description Code DUNTK9874DE01 R5062 VRS-CY1JF332F J 3.3k 1/16W Metal Oxide R5063 VRS-CY1JF332F J 3.3k 1/16W Metal Oxide SIGNAL UNIT (Continued) R5064 VRS-CY1JF332J J 3.3k 1/16W Metal Oxide R5066 VRS-CY1JF821J...
  • Seite 141 XV-ZW60E Ref. No. Part No. Description Code Ref. No. Part No. Description Code DUNTK9756DE02 Q1023 VS2SA1036KR-1 J 2SA1036KR Q1024 VS2SC2411KR-1 J 2SC2411KR OUTPUT UNIT Q1025 VS2SA1036KR-1 J 2SA1036KR Q1026 VS2SC2411KR-1 J 2SC2411KR INTEGRATED CIRCUITS Q1027 VS2SA1036KR-1 J 2SA1036KR Q1028 VS2SC2411KR-1...
  • Seite 142 XV-ZW60E Ref. No. Part No. Description Code Ref. No. Part No. Description Code DUNTK9756DE02 C1053 VCCCCY1HH100D J 10p Ceramic C1054 VCCCCY1HH100D J 10p Ceramic OUTPUT UNIT (Continued) C1055 VCCCCY1HH100D J 10p Ceramic C1056 VCCCCY1HH100D J 10p Ceramic D2512 VHDDAN202K/-1 J Diode C1057 VCKYCY1CF104Z J 0.1...
  • Seite 143 XV-ZW60E Ref. No. Part No. Description Code Ref. No. Part No. Description Code DUNTK9756DE02 C2518 VCKYCY1HB103K J 0.01 Ceramic C2519 VCKYCY1CF104Z J 0.1 Ceramic OUTPUT UNIT (Continued) C2520 VCKYCY1CF104Z J 0.1 Ceramic C2521 VCKYCY1CF104Z J 0.1 Ceramic C1132 VCKYCY1EF104Z J 0.1...
  • Seite 144 XV-ZW60E Ref. No. Part No. Description Code Ref. No. Part No. Description Code DUNTK9756DE02 R1142 VRS-CY1JF392J J 3.9k 1/16W Metal Oxide R1143 VRS-CY1JF392J J 3.9k 1/16W Metal Oxide OUTPUT UNIT (Continued) R1144 VRS-CY1JF102J J 1.0k 1/16W Metal Oxide R1146 VRS-CY1JF101J...
  • Seite 145 XV-ZW60E Ref. No. Part No. Description Code Ref. No. Part No. Description Code DUNTK9756DE02 R1304 VRS-CY1JF000J 1/16W Metal Oxide R1305 VRS-CY1JF102J J 1.0k 1/16W Metal Oxide OUTPUT UNIT (Continued) R1306 VRS-CY1JF101J J 100 1/16W Metal Oxide R1307 VRS-CY1JF000J 1/16W Metal Oxide...
  • Seite 146 XV-ZW60E Ref. No. Part No. Description Code Ref. No. Part No. Description Code DUNTK9756DE02 R1479 VRS-CY1JF000J 1/16W Metal Oxide R2001 VRS-CY1JF103J J 10k 1/16W Metal Oxide OUTPUT UNIT (Continued) R2002 VRS-CY1JF471J J 470 1/16W Metal Oxide R2003 VRS-CY1JF471J J 470...
  • Seite 147 XV-ZW60E Ref. No. Part No. Description Code Ref. No. Part No. Description Code DUNTK9756DE02 R2523 VRS-TX2HF100J J 10 1/2W Metal Oxide R2524 VRS-TX2HF100J J 10 1/2W Metal Oxide OUTPUT UNIT (Continued) R2526 VRS-CY1JF103J J 10k 1/16W Metal Oxide R2527 VRS-CY1JF562J J 5.6k 1/16W Metal Oxide...
  • Seite 148 XV-ZW60E Ref. No. Part No. Description Code Ref. No. Part No. Description Code DUNTK9756DE02 DUNTK9757DE02 OUTPUT UNIT (Continued) INPUT UNIT FB1026 RBLN-0059CEZZ J Ferrite Bead INTEGRATED CIRCUITS FB1028 RBLN-0059CEZZ J Ferrite Bead IC401 VHiCXA2069Q-1 J CXA2069Q FB1029 RBLN-0059CEZZ J Ferrite Bead...
  • Seite 149 XV-ZW60E Ref. No. Part No. Description Code Ref. No. Part No. Description Code DUNTK9757DE02 C468 VCCCCY1HH330J J 33p Ceramic C469 VCKYCY1CF104Z J 0.1 Ceramic INPUT UNIT (Continued) C470 VCCCCY1HH330J J 33p Ceramic C471 VCKYCY1CF104Z J 0.1 Ceramic COIL C472 VCKYCY1CF104Z J 0.1...
  • Seite 150 XV-ZW60E Ref. No. Part No. Description Code Ref. No. Part No. Description Code DUNTK9757DE02 R415 VRS-TV1JD750J J 75 1/16W Metal Oxide R416 VRS-CY1JF101J J 100 1/16W Metal Oxide INPUT UNIT (Continued) R417 VRS-CY1JF000J 1/16W Metal Oxide R418 VRS-CY1JF000J 1/16W Metal Oxide...
  • Seite 151 XV-ZW60E Ref. No. Part No. Description Code Ref. No. Part No. Description Code DUNTK9757DE02 SC401 QSOCZ0012FJZZ J Socket, 28-pin (CA) SC402 QSOCZ0012FJZZ J Socket, 28-pin (TN) INPUT UNIT (Continued) SC403 QSOCN0344FJZZ J Socet, Computer IN SC404 QSOCN0345FJZZ J Socket, RS232C...
  • Seite 152 XV-ZW60E Ref. No. Part No. Description Code Ref. No. Part No. Description Code DUNTK9875DE01 DUNTK9382DE11 INFRARED R/C RECEIVER UNIT LED UNIT CAPACITORS INTEGRATED CIRCUITS C7501 VCEAPF0JW107M J 100 6.3V Electrolytic IC7301 VHiTDA1517/-1 J TDA1517/N2 C7502 RC-KZ0416CEZZ J 10 Ceramic DIODES...
  • Seite 153 XV-ZW60E Ref. No. Part No. Description Code Ref. No. Part No. Description Code CDENC0276CE01 D1703 95KUBC0190BK J Diode ERC38-05 D1704 95KUBC0125DK J Diode ERA15-06 POWER/BALLAST UNIT D1705 95KUBY0020AK J Diode (Chip) 1SS355 D1706 95KUBC0248AK J Diode 05NU42 INTEGRATED CIRCUITS D1707 95KUBC0318AK...
  • Seite 154 XV-ZW60E Ref. No. Part No. Description Code Ref. No. Part No. Description Code CDENC0276CE01 R121 95KUEXDAK472 J 4.7k 1/4W Chip R122 95KUEXCAS103 J 10k 1/10W Chip POWER/BALLAST UNIT (Continued) R123 95KUEXCAS103 J 10k 1/10W Chip R124 95KUEXDAK222 J 2.2k 1/4W Chip...
  • Seite 155 XV-ZW60E Ref. No. Part No. Description Code Ref. No. Part No. Description Code CDENC0276CE01 95KLRZ6486ZR J Heat Sink 95KLRZ6460ZP J Heat Sink POWER/BALLAST UNIT (Continued) 95KLRZ6343ZP J Heat Sink 95KLRZ6554ZR J Heat Sink R767 95KUEXDAK102 J 1k 1/4W Chip LHLDZ2035CEKZ...
  • Seite 156 – Top Cabinet — 10-5 95KECB7881ZZ J Cooling Fan GNETC0106CEZZ J Speaker Net, x2 10-6 95KGZZ5403ZZ J Shield HBDGB3107CESA J SHARP Badge 10-9 XBSSD30P08000 J Screw, x2 LHLDZ2037CEKZ J Holder (L), x2 10-10 XEBSF30P08000 J Screw, x2 LHLDZ2038CEKZ J Holder (R), x2...
  • Seite 157: Cabinet And Mechanical Parts/ Geäuse Und Mechanische Bauteile

    XV-ZW60E CABINET AND MECHANICAL PARTS/ Ref. No. Part No. Description Code Ref. No. Part No. Description Code GEÄUSE UND MECHANISCHE BAUTEILE...
  • Seite 158 XV-ZW60E Ref. No. Part No. Description Code Ref. No. Part No. Description Code CABINET AND MECHANICAL PARTS OPTICS MECHANISM PARTS (Continued) Not Available – Infrared R/C Receiver Unit — CCHSK0051CEK3 J Optics Mecha Ass’y Not Available – LED Unit —...
  • Seite 159: Optics Mechanism Parts/ Teile Für Optikmechanismus

    XV-ZW60E OPTICS MECHANISM PARTS/ Ref. No. Part No. Description Code Ref. No. Part No. Description Code TEILE FÜR OPTIKMECHANISMUS...
  • Seite 160: Supplied Accessories

    XV-ZW60E Ref. No. Part No. Description Code Ref. No. Part No. Description Code OPTICS MECHANISM PARTS SUPPLIED ACCESSORIES (Continued) 8-69 RH-HZ0051CEZZ J Thermistor ACCESSORIES 8-70 9EQCK0002KKZZ J Stroke Switch, x2 å QACCV4002CEZZ J AC Cord (Europe) 8-71 9EQCK0001KKZZ J Linear Position Sensor å...
  • Seite 161: Verpacken Des Geräts

    XV-ZW60E Ref. No. Part No. Description Code Ref. No. Part No. Description Code PACKING OF THE SET / VERPACKEN DES GERÄTS Buffer Material for Lens/ Polstermaterial für objektiv Polystyrene Cover/ AC Cord/ Polystyrol-Verpackung Netzkabel Infrared R/C Unit/ VGA Cable/ Fernbedienung...

Inhaltsverzeichnis