Optional Accessories; Controls - Fohhn FP1pro Bedienungsanleitung

4.2 Optional Accessories

FP1 /
pro CD
• Padded carrying bag for FP1
• Raincover for FP1 /
pro CD
• SHP1 stand adapter for FP1
• WHP1 wall bracket for FP1
• WHP1 wall bracket for FP1
• Loudspeakerstand
• Microphone stand with boom
• Carrying bag for two stands
• Music-Tray for portable music-playing equipment +
microphone, easy tomount to speaker stands
• ADESSO Design Desk

4.3 Controls

(Refer to illustrations on page 18 to 20)
Most controls on the FP1
speaker. The squelch control (10) and the channel selector switch
(11) for the radio receiver, which is fitted as an option.
A sturdy carrying handle is integrated in the rear panel of the
enclosure.
(1) recharge battery
Input jack for charging the integrated battery or operating the
EasyPort on AC power. Please use the AC adapter
(2) Power pack charge status display
Quick-charge mode, charging time 6 hours. If the yellow LED
lights up continuously, the FP1
the LED then flashes once the power pack starts charging.
(3) power switch
Switches power to the EasyPort FP1
amplifier on and off but does not affect the charging circuit.
(4) Status display
Status LED, multi-coloured, charge status of the power pack is
indicated by a flashing sequence.
When the FP1 is switched on, the LED lights up green if
pro/CD
the power pack is fully charged.
If the power pack voltage is decreasing, the LED lights up red
continuously.
After the LED is lit for 10 seconds, the FP1
to prevent the power pack from an exhaustive discharge.
/
pro CD
,
/
pro CD
/ provits and tilts
pro CD,
/ speaker removable
pro CD,
are located on the back of the
pro/CD
is in quick-charge mode,
pro/CD
audio section and
pro/CD
pro/CD
13
music
(5) line input l/r
These two RCA jacks allow you to conect a CD player, cassette
recorder, or other line level source to your EasyPort using a
stereo RCA cable (not supplied). The stereo input signal is
internally summed to mono.
Input sensitivity is 100 mV into 10 kΩ for nominal level.
(6)
volume
This rotary potentiometer sets the loudness volume of the
audio source connected to the line input l/r jacks (5).
(7) line out l/r
These two RCA jacks allow you to connect either a recorder or
another EasyPort to your unit using a stereo RCA cable (not
supplied).
The two jacks are internally paralleled and carry the output
signal of the built-in mixer with all the volume and EQ settings
you made. The output voltage at nominal level is 0,5 V into
200 Ω source impedance.
wired mic
(8) input
This balanced female XLR connector allows you to connect a
wired microphone (optional) via a standard microphone cable
with a male XLR connector (optional). Since the microphone
INPUT provides 12 V phantom power you can connect both
dynamic and electret or condenser microphones.
Input sensitivy for nominal level is 2 mV into 1 kΩ.
Pin 1 is ground, pin 2 „hot" (inphase), pin 3 return.
(9) volume
This rotary potentiometer sets the loudness volume of the
microphone connected to the INPUT connector (8).
wireless mic
(10) wireless receiver
(11)
(10) squelch, (11) channel
For details on the optional wireless receiver please refer to the
enclosed instruction manual for the receiver.
(12) volume
This rotary potentiometer sets the loudness volume of the
wireless microphone.
EQ The two-band equalizer acts on the microphone and line
inputs.
(13) bass
Rotary control for cutting or boosting the low frequencies.
(14) treble
Rotary control for cutting or boosting the high frequencies.
switches off