Herunterladen Inhalt Inhalt Diese Seite drucken

Yamaha RX-A3020 Anleitung Zur Schnelleinrichtung Seite 4

Vorschau ausblenden Andere Handbücher für RX-A3020:
Inhaltsverzeichnis

Werbung

Verfügbare Sprachen
  • DE

Verfügbare Sprachen

  • DEUTSCH, seite 18
3
Connecting speakers/subwoofer
• Under its default settings, the unit is configured for 8-ohm
speakers. When connecting 6-ohm speakers, set the unit's
speaker impedance to "6 Ω MIN". For details, see "Setting the
speaker impedance" in "Owner's Manual".
• Use a subwoofer equipped with built-in amplifier.
• Before connecting the speakers, remove the unit's power cable
from the AC wall outlet and turn off the subwoofer.
• Ensure that the core wires of the speaker cable do not touch
each other or come into contact with the unit's metal areas. This
may damage the unit or the speakers. If the speaker cables
short circuit, "Check SP Wires" will appear on the front display
when the unit is turned on.
Connecting speaker cables
Speaker cables have two wires. One is for connecting the
negative (–) terminals of the unit and the speaker, and the
other is for the positive (+) terminals. If the wires are
colored to prevent confusion, connect the black wire to
the negative and the other wire to the positive terminals.
a Remove approximately 10
mm (3/8") of insulation
+ (red)
b
from the ends of the
speaker cable and twist
the bare wires of the cable
firmly together.
– (black)
b Loosen the speaker terminal.
c Insert the bare wires of the cable into the gap on the side
(upper right or bottom left) of the terminal.
d Tighten the terminal.
Using a banana plug
(U.S.A., Canada, China,
Banana plug
Australia and General
models only)
a Tighten the speaker
terminal.
b Insert a banana plug into the end of the terminal.
1
Connect the front speakers (1/2)
to the FRONT (//\) and the center
speaker (3) to the CENTER terminal.
The unit (rear)
FRONT
SURROUND
SUR. BACK
SUBWOOFER
SURROUND
SURROUND BACK
R
L
R
E
c
F R
O N
T
a a
d
9
4
6
a
F R
O N
T
b
CENTER
ZONE OUT/PRE OUT
PRE OUT
(SINGLE)
(FRONT)
1
2
ZONE 2 /
ZONE 3 /
(REAR)
F.PRESENSE
R.PRESENSE
FRONT
SURROUND
SUR. BACK
SUBWOOFER
CENTER
SPEAKERS
ZONE 2/ZONE 3/F.PRESENCE/
ZONE 2/ZONE 3/R.PRESENCE
CENTER
FRONT
L
R
L
BI–AMP
R
L
EXTRA SP1
EXTRA SP2
R
SINGLE
R
1
2
3
5
7
2
Connect the surround speakers
(4/5) to the SURROUND (//\)
terminals.
CENTER
ZONE OUT/PRE OUT
PRE OUT
(SINGLE)
The unit (rear)
ZONE 2 /
ZONE 3 /
FRONT
SURROUND
SUR. BACK
SUBWOOFER
F.PRESENSE
R.PRESENSE
FRONT
SURROUND
SUR. BACK
SPEAKERS
SURROUND
SURROUND BACK
ZONE 2/ZONE 3/R.PRESENCE
R
L
R
L
R
L
L
EXTRA SP2
SINGLE
E
1
9
3
4
6
(FRONT)
1
2
(REAR)
SUBWOOFER
CENTER
ZONE 2/ZONE 3/F.PRESENCE/
CENTER
FRONT
R
L
BI–AMP
EXTRA SP1
R
L
R
2
5
7
3
En

Werbung

Inhaltsverzeichnis
loading

Diese Anleitung auch für:

Rx-a2020

Inhaltsverzeichnis