Care And Maintenance; Replacing The Power Cable; Cleaning, Maintenance And Ordering Of Spare Parts - EINHELL BT-MR 550 Originalbetriebsanleitung

Anleitung_BT_MR_550_SPK7:_
GB
setting of the depth stop (12).
After finishing the work, return the routing head to
the upper position and switch the machine off.
Clean the machine and clamping fixture and
lubricate if necessary.
8.1.1 Countersinking and center-drilling
Remember that countersinking should be carried
out with a low cutting speed and low feed, while
center-drilling should be carried out with a high
cutting speed and low feed.
8.2 Face routing
Clamp the clamping chuck and tool in place (see
chapter 7.1) and lock them with the tie rod (19).
Tighten the chuck using the chuck key.
Set the correct rotational speed
(see chapter 7.1-7.2).
Important: Do not change rotational speed
ranges (L and H) while the spindle is running!
Clamp the workpiece firmly using a machine vice
or by means of clamping claws.
Bring the table into the desired position (X or Y
direction).
Set the depth stop (see chapter 7.4.1), making
sure that the tool does not touch the workpiece.
Remove from the working area any objects that
are no longer needed.
Switch the machine on and set the desired spindle
speed using the speed selector switch (6).
Carry out the routing work. To do this, adjust the
compound table in the X and Y direction using the
hand cranks (see 7.5.3).
After finishing the work, switch the machine off
and return the routing head (1) to the upper
position.
Clean the machine and clamping fixture and
lubricate if necessary.
The work table must be cleaned and lubricated
again after the machine has been used.

9. Care and maintenance

Always pull out the power plug before carrying
out care and maintenance work! Machine
maintenance is required at regular intervals
(depending on how often it is used). The
maintenance work should be documented exactly.
Keep the tapered shanks and routing cutter clean.
For added protection, identical routing cutters are
best kept in a box when not in use.
Check that the whole electric circuit (switches,
plugs, contacts etc.) is functioning properly.
22
28.02.2011 10:08 Uhr Seite 22
To prevent further damage and injury, please
contact our Customer Services department if any
faults occur which require more than the normal
maintenance. The address is given in the warranty
card.
Check that the routing head can move easily and
make sure that it has not worked loose.
Check the spindle for excess vibration.
Check that all the screw connections are tight.
9.1 Lubrication
If consistently good results are to be achieved and
the machine is to be protected against corrosion, it
must be lubricated and greased at regular intervals.
Spread the lubricating oil or grease evenly using a
brush or non-fluffy cloth.
Lubricating points and lubricants:
All bare parts of the machine:
Tie rod on column:
Machine table:
Fine feed mechanism:
Saddle slide feed spindle:
Cross slide feed spindle:
Routing head inverted V-track:
Routing head pivot bearing:
Cross slide inverted V-track:
Saddle slide inverted V-track:

10. Replacing the power cable

If the power cable for this equipment is damaged, it
must be replaced by the manufacturer or its after-
sales service or similarly trained personnel to avoid
danger.
11. Cleaning, maintenance and
ordering of spare parts
Always pull out the mains power plug before starting
any cleaning work.
11.1 Cleaning
Keep all safety devices, air vents and the motor
housing free of dirt and dust as far as possible.
Wipe the equipment with a clean cloth or blow it
with compressed air at low pressure.
We recommend that you clean the device
immediately each time you have finished using it.
Clean the equipment regularly with a moist cloth
and some soft soap. Do not use cleaning agents
or solvents; these could attack the plastic parts
of the equipment. Ensure that no water can seep
into the device.
Lubricating oil
Lubricating oil
Lubricating oil
Lubricating oil
Lubricating oil
Lubricating oil
Lubricating grease
Lubricating grease
Lubricating grease
Lubricating grease