Herunterladen Inhalt Inhalt Diese Seite drucken

Replacing The Power Cable; Cleaning, Maintenance And Ordering Of Spare Parts - EINHELL TH-MA 1300 Originalbetriebsanleitung

Mauernutfräse
Vorschau ausblenden Andere Handbücher für TH-MA 1300:
Inhaltsverzeichnis

Werbung

Verfügbare Sprachen
  • DE

Verfügbare Sprachen

  • DEUTSCH, seite 1
(6).
Take off the guard hood (3).
Swing the depth stop (7) down and away.
While holding the spindle lock (2) pressed,
unscrew the outer flange (b) with the supplied
flange nut wrench (c).
Remove the spacer rings (d).
Remove the inner flange (e).
Thoroughly clean the spacer rings, flanges
and fastening parts.
Fit the inner flange (e).
Then fit the diamond cutting wheels together
with the spacer rings (d) to achieve the desi-
red groove
Important! Take account of the direction of rotati-
on when fi tting the diamond cutting wheels!
Important! Diamond cutting wheels must always
be replaced as pairs!
You have 6 spacer rings available, each one
being approx. 3.5mm in width. Please note
that the width of the groove is determined by
the sum of the spacer rings between the dia-
mond cutting wheels and the thickness of the
cutting wheels.
All 6 spacer rings (d) have to be fitted irres-
pective of the desired groove width.
Now re-assemble the device in reverse order,
taking care in so doing to ensure that all parts
are fitted correctly and tightly.
Important!
Only ever press the spindle lock when the
motor and grinding spindle are at a stand-
still!
You must keep the spindle lock pressed while
you change the wheel!
6.3 Motor
It is vital for the motor to be well ventilated during
operation. Be sure, therefore, to keep the ventilati-
on holes clean at all times.
6.4 Working with the masonry channel cutter
(Fig. 12)
Important! The device is fi tted with an overload
cut-out. The motor will cut out if overloaded. Re-
lieve the load on the motor immediately and allow
the masonry channel cutter to cool down for ap-
prox. 1 minute without load.
Important! The device is suitable for dry cutting
only!
Anl_TH_MA_1300_SPK1.indb 16
Anl_TH_MA_1300_SPK1.indb 16
GB
Use a cable/pipe detector to check for conce-
aled electric cables and gas and water pipes
in the wall before you start using the masonry
channel cutter.
Select the desired groove width (see 6.2) and
groove depth (see 5.1).
Important! Only ever guide the device along the
workpiece while switched on.
Place the device against the wall with the rol-
ler (10) against the wall.
Switch on the device and then cut slowly into
the wall until the stop (7) rests against the
width.
wall.
Now you can cut the groove in the wall. Take
care with the cutting direction (a) as you do
so. The device must always be handled on
a counterrotating basis otherwise there is a
risk that it may be forced out of the cut in an
uncontrolled manner.
Important! Cut in a straight line only. It is not pos-
sible to cut curves.
At the end of the groove, swing the device out
of the groove before you switch it off.
You can then cut out the ridge between the
two grooves with a chisel.
It is prohibited to use the machine on as-
bestos materials!

7. Replacing the power cable

If the power cable for this equipment is damaged,
it must be replaced by the manufacturer or its
after-sales service or similarly trained personnel
to avoid danger.
8. Cleaning, maintenance and
ordering of spare parts
Always pull out the mains power plug before star-
ting any cleaning work.
8.1 Cleaning
Keep all safety devices, air vents and the
motor housing free of dirt and dust as far as
possible. Wipe the equipment with a clean
cloth or blow it with compressed air at low
pressure.
We recommend that you clean the device
immediately each time you have finished
- 16 -
09.04.13 13:07
09.04.13 13:07

Werbung

Inhaltsverzeichnis
loading

Diese Anleitung auch für:

43.507.30

Inhaltsverzeichnis