Intended Use; Additional Battery Safety Warnings; Know Your Product - Ryobi Rid18X1-0 Originalanleitung

EN ORIGINAL INSTRUCTIONS
Safety, performance, and dependability have been given top
priority in the design of your impact driver.

INTENDED USE

The impact driver is intended to be used only by adults who
have read and understood the instructions and warnings in
this manual, and can be considered responsible for their
actions.
The product is intended for fastening and removing screws
and bolts.
The product is intended for consumer use only.
Do not use the product for any other purpose. Use of the
product for operations diff erent from intended could result in
a hazardous situation.
WARNING! Read all safety warnings, instructions,
illustrations and specifications provided with this
power tool. Failure to follow all instructions listed below
may result in electric shock, fi re and/or serious injury.
Save all warnings and instructions for future reference.
IMPACT DRIVER SAFETY WARNINGS
■
Hold the power tool by insulated gripping surfaces,
when performing an operation where the fastener
may contact hidden wiring. Fasteners contacting a
"live" wire may make exposed metal parts of the power
tool "live" and could give the operator an electric shock.
■
Clamp workpiece with a clamping device. Unclamped
workpieces can cause severe injury and damage.
■
Dust created by operating the product can cause
respiratory injury. Wear appropriate dust control mask
with filters suitable for protecting against particles from
the material being worked on.
■
Injuries may be caused, or aggravated, by prolonged
use of a tool. When using any tool for prolonged periods,
ensure you take regular breaks.
■
The product will restart automatically if stalled. Switch
off the product immediately if it stalls. Do not switch
on the product again while it is still stalled, as doing so
could trigger a sudden recoil with a high reactive force.
Determine why the product stalled and rectify this,
paying heed to the safety instructions.
■
Ambient temperature range for tool during operation is
between 0 °C and 40 °C.
■
Ambient temperature range for tool storage is between
0 °C and 40 °C.
■
The recommended ambient temperature range for the
charging system during charging is between 10 °C and
38 °C.

ADDITIONAL BATTERY SAFETY WARNINGS

■
To reduce the risk of fire, personal injury, and product
damage due to a short circuit, never immerse your
tool, battery pack, or charger in fluid or allow fluid to
flow inside them. Corrosive or conductive fluids, such
as seawater, certain industrial chemicals, and bleach
or bleach-containing products, etc., can cause a short
circuit.
■
Ambient temperature range for battery during use is
between 0 °C and 40 °C.
■
Ambient temperature range for battery storage is
between 0 °C and 20 °C.
TRANSPORTING LITHIUM BATTERIES
Transport the battery in accordance with local and national
provisions and regulations.
Follow all special requirements on packaging and labelling
when transporting batteries by a third party. Ensure that
no batteries can come in contact with other batteries
or conductive materials while in transport by protecting
exposed connectors with insulating, non-conductive caps or
tape. Do not transport batteries that are cracked or leaking.
Check with the forwarding company for further advice.

KNOW YOUR PRODUCT

See page 43.
1. Chuck
2. Direction of rotation selector
3. Variable speed switch trigger
4. Handle, insulated gripping surface
5. LED light
6. Battery port
7. Low speed
8. Medium speed
9. High speed
10. "A" mode
11. Mode selection button
12. Single bit
13. Single bit
14. Bit adaptor
15. Belt clip screw
16. Belt clip
17. Operator's manual
18. Battery pack
19. Charger
*Use the "A" mode to drive screws when better control
is required. This mode starts at a lower speed and then
increases to fi nish driving in the screw.
In reverse direction, this mode rotates in 6 pulses moving up
to a controlled reverse speed designed to remove screws
with damaged heads.
MAINTENANCE
■
The product should never be connected to a power
supply when assembling parts, making adjustments,
cleaning, performing maintenance, or when the product
is not in use. Disconnecting the product from the power
supply will prevent accidental starting that could cause
serious injury.
■
When servicing, use only original manufacturer's
replacement parts, accessories, and attachments. Use
of any other parts may create a hazard or cause product
damage.
■
Avoid using solvents when cleaning plastic parts. Most
plastics are susceptible to various types of commercial
EN
FR
DE
ES
IT
NL
PT
DA
SV
FI
NO
RU
PL
CS
HU
RO
LV
LT
ET
HR
SL
SK
BG
UK
TR
EL
3