Technical Data - Renkforce Rf-Tpcd-350 Bedienungsanleitung

The computer will automatically detect and install the hard drive. It will appear under
Æ
"Computer" as a newly added hard drive. You can read from and write to it.
7.3 Clone mode (clone data from source drive to target drive)
Important:
– Data will be copied from the source drive to the target drive.
– All existing data on the target drive will be lost.
– Always back up important data before cloning.
– Do not remove a drive or disconnect the power supply during cloning.
Notes:
– For clone mode, don't connect to a PC.
– Don't insert the drive in the wrong slot.
– The capacity of the target drive must be greater than or equal to that of the source
drive.
1. Insert the source drive with data and the target drive in the corresponding slots.
2. Switch the two keys 1/2 of the clone setting switch (8) according to the diagram.
NVMe to SATA SD to NVMe
1 & 2 up 1 down & 2 up
3. Connect the DC IN port to the power supply using the supplied power adapter. Then press
the power button (3) to power on.
The corresponding indicator lights will be on.
Æ
4. Press the clone button (10) twice quickly.
The 25% light will blink, indicating that cloning has started.
Æ
When the 100% light turns solid, the cloning process is complete.
Æ
5. Press the power button (3) to power off. Then remove the drives.
8 Cleaning and care
Important:
– Do not use aggressive cleaning agents, rubbing alcohol or other chemical solutions.
They damage the housing and can cause the product to malfunction.
– Do not immerse the product in water.
1. Disconnect the product from the power supply.
2. Clean the product with a dry, fibre-free cloth.
9 Disposal
This symbol must appear on any electrical and electronic equipment placed on the
EU market. This symbol indicates that this device should not be disposed of as
unsorted municipal waste at the end of its service life.
Owners of WEEE (Waste from Electrical and Electronic Equipment) shall dispose
of it separately from unsorted municipal waste. Spent batteries and accumulators,
which are not enclosed by the WEEE, as well as lamps that can be removed from
the WEEE in a non-destructive manner, must be removed by end users from the
WEEE in a non-destructive manner before it is handed over to a collection point.
Distributors of electrical and electronic equipment are legally obliged to provide free take-back
of waste. Conrad provides the following return options free of charge (more details on our
website):
in our Conrad offices
at the Conrad collection points
at the collection points of public waste management authorities or the collection points set
up by manufacturers or distributors within the meaning of the ElektroG
End users are responsible for deleting personal data from the WEEE to be disposed of.
It should be noted that different obligations about the return or recycling of WEEE may apply in
countries outside of Germany.
SD to SATA SATA to NVMe
1 up & 2 down 1 & 2 down

10 Technical data

10.1 Power adapter
Input.............................................. 100 - 200 V/DC, 50/60 Hz, max. 0.5 A
Output ........................................... 5 V/DC 3 A 15 W
10.2 Product
Input.............................................. 5 V/DC, 3 A via USB-C
Interface ........................................ USB-C
Data transfer speed ...................... Up to10 Gbps (NVMe)
System requirement ..................... Windows
10.3 Supported drives
SSD type ...................................... M.2 SATA SSD (Key B+M ); M.2 PCIe NVMe SSD (Key M)
SSD size ....................................... 2230/2240/2260/2280/22110 mm
SD card ......................................... SD Express 7.1
Memory size ................................. Max. 8 TB
10.4 Other
Operating temperature ................. 0 to +70 °C
Operating humidity ....................... 10 – 80 % RH (non-condensing)
Storage temperature ..................... -10 to +80 °C
Storage humidity ........................... 8 – 90 % RH (non-condensing)
Material ......................................... Plastic (case)
Dimensions (W x H x D) ............... 79 x 19 x 77 mm
Weight .......................................... 157 g
This is a publication by Conrad Electronic SE, Klaus-Conrad-Str. 1, D-92240 Hirschau (www.conrad.com). All rights in-
cluding translation reserved. Reproduction by any method, e.g. photocopy, microfilming, or the capture in electronic data
processing systems require the prior written approval by the editor. Reprinting, also in part, is prohibited. This publication
represents the technical status at the time of printing.
Copyright 2025 by Conrad Electronic SE.
®
®
, macOS, Linux
®
*3348027_V3_0525_02_dm_mh_en