Technical Data - Renkforce RF-4499452 Bedienungsanleitung

3. Connect the peripheral device to one of the listed USB-A ports.
Important! If your device has minimum power requirements, ensure the port can meet them.
4. Connect the power adapter.
» The peripheral device is ready for use.
Charging or powering devices
Learn on which ports devices (e.g. smartphone) can be charged, and how to charge and power them.
Understand the limitations of available charging ports.
Charging and powering a notebook with a USB-C™ connector requires an additional power supply. This
case is described separately.
Important: Power supply is limited
Power supplied by the power adapter is limited. It means:
• The product may limit the power supplied to simultaneously connected devices.
• Charging times may not meet your expectations.
• Charging may not be possible at all.
Ports:
Unit Port Component
USB-C™ Host
USB-C™ (PD3.0)
Power
USB-C™ USB-C
USB-A 3,5
USB-A 11,12
Connect as follows:
1. (If connected) disconnect the power adapter.
2. Connect the device you want to charge or power to one of the listed ports.
Important! If your device has a minimum power requirement, ensure the port can meet it.
3. Connect the power adapter.
» The connected device is powered/charging starts.
Powering and charging a notebook:
To power and charge a notebook you need an additional power source that meets the Power Delivery (PD)
specification and the power requirements of the notebook.
1. Connect a suitable power supply to the USB-C™ (PD3.0) port Power.
2. Connect the notebook to the USB-C™ port Host.
Connecting screens
Connect a screen to display video content received from a host device.
You can connect more than one screen: unit
Make sure to correctly match a video port with the associated host port of the same unit (
Unit Port Component
HDMI
USB-C™ (IN) HOST
USB-C™ (IN) Host
HDMI
HDMI
VGA
Connect as follows:
1. (If connected) disconnect the power adapter.
2. Locate the required port within the selected unit (
3. Connect a screen to the selected video port (HDMI or VGA). If needed, connect more screens.
4. Connect the video source device (e.g. computer) to the associated host port (HOST or Host).
- Note: the video source device must output video in HDMI format.
5. Connect the power adapter.
» Video is displayed on the connected screen(s).
6. (If needed) adjust screen settings on the video source device/screen(s).
How sound is controlled:
When HDMI and VGA ports are in use at the same time, sound output to screens that support sound is as
follows:
OS Port Component
Windows HDMI Select 6 or 8 or 9
®
macOS HDMI Select 6 or 8,9
Supply/Consume Limitations
- max. 20 V/DC
14 Consume - max. 87 W (requires power
from USB-C™ port Power)
13 Consume / Supply
- 5 V/DC
4 Consume
- max. 3 A / max. 15 W
- 5 V/DC
Consume
- max. 1.5 A / max. 7.5 W
- 5 V/DC
Consume
- max. 0.9 A / max. 4.5 W
: 1 screen / unit : up to 3 screens.
Limitations
6 Video signal: 4K2K 30 Hz / 3840 x 2160
7
14
Video signal:
8
- 4K2K 30 Hz / 3840 x 2160
- 1080P (if used in combination with VGA)
Video signal:
- 4K2K (60 Hz) / 3840 x 2160
(input source supports DP1.4)
9
- 4K2K (30 Hz) / 3840 x 2160
(input source supports DP1.2)
- 1080P (if used together with the VGA port)
10 Video signal: 1080p (60 Hz)
or ).
Sound output
Yes
Yes
Using an analogue microphone or headset
Connect a microphone or headset (CTIA Standard) to transfer sound to a receiver device (e.g. computer,
smartphone).
Ports:
Unit Port
3.5 mm jack socket
USB-C™ (IN) Host
Connect as follows:
1. (If connected) disconnect the power adapter.
2. Connect a microphone or headset with a 3.5 mm jack to the jack socket.
3. Connect the host device to the USB-C™ port Host.
4. Connect the power adapter.
» The microphone/headset is ready for use.
5. Adjust microphone or headset settings on the host device.
Adding a network connection
Connect the product to your local area network (LAN) to provide the host device with access to network
resources.
Ports:
Unit Port
USB-C™ Host
Network port
Connect as follows:
1. Connect the network port on the product to your router or network switch using a 1:1 fully wired network
cable.
2. Connect the host device to the USB-C™ port Host.
Wait for the network resources to show up on the host device. This may take some time.

Technical data

a) Docking station
Operating voltage/current ..................... 12 V/DC, 3 A
Supported OS ....................................... Windows
Operating conditions ............................. 0 to +45 °C, 10 - 85 %
Storage conditions ................................ -10 to +70 °C, 5 - 90 %
Dimensions (W x H x D) ....................... 120 x 63 x 73.5 mm
Weight .................................................. 330 g
b) Power adapter
Input voltage/current ............................. 100 – 240 V/AC, 50/60 Hz, max. 1.2 A
Output voltage/current/power ............... 12 V/DC, 3 A, 36 W
c) Ports
or ).
The component numbers refer to the section Components.
Component Port
2 3.5 mm jack socket
3,5 USB-A
4 USB-C™ USB-C
6,8 HDMI
9 HDMI
10 VGA
11,12 USB-A
13 USB-C™ Power
14 USB-C™ (IN) Host
16 Network port
This is a publication by Conrad Electronic SE, Klaus-Conrad-Str. 1, D-92240 Hirschau (www.conrad.com).
All rights including translation reserved. Reproduction by any method (e.g. photocopying, microfilming or the capture in
electronic data processing systems) requires prior written approval from the editor. Reprinting, also in part, is prohibited.
This publication reflects the technical status at the time of printing.
Copyright 2020 by Conrad Electronic SE.
Component
2
14
Component Limitations
14
16 - max. 1000 Mbit/s
RT, 10 (32/64 bit), macOS 10.12.x to macOS 10.15.x,
®
Linux 2.6, Android 6.0 to 9.0, iPadOS 13,
Windows Phone 10
relative humidity (non-condensing)
relative humidity (non-condensing)
Specifications
Ø 3.5 mm, CTIA Standard
- USB 3.0 / USB 3.1 GEN1 port
- max. 5 GBit/s
- 5 V/DC / max. 1.5 A / max. 7.5 W
- USB 3.0 / USB 3.1 GEN1 port
- max. 5 GBit/s
- 5 V/DC / max. 3 A / max. 15 W
Video signal: 4K2K 30 Hz / 3840 x 2160
Video signal:
- 4K2K (60 Hz) / 3840 x 2160 (input source supports DP1.4)
- 4K2K (30 Hz) / 3840 x 2160 (input source supports DP1.2)
Video signal: 1080p (60 Hz)
- USB 3.0 / USB 3.1 GEN1 port
- max. 5 GBit/s
- 5 V/DC / max. 0.9 A / max. 4.5 W
- PD3.0
- max. 20 V/DC
- max. 100 W
- max. 20 V/DC
- max. 87 W*
*if power is supplied on the USB-C™ (PD3.0) Power port
- Ethernet
- max. 1000 Mbit/s
*2249726_v3_1120_jh_m_3L_(5)