Technical Data; Power Adapter - Renkforce Rf-Hd-Ds-01 Bedienungsanleitung

7 Cloning drives
With the offline clone function you can clone the data of the source drive to the target drive
without a computer.
Important:
– The target drive must have at least the same capacity as the source drive.
– All data stored on the target drive will be deleted at the beginning of the cloning.
– Both drives will have the same ID after cloning. If you connect both drives to a com-
puter only one drive will be shown in the file manager.
– If two drives have the same ID (for example after cloning two SSD drives), only one
will show in the file manager of the computer. Under the Windows® operating system,
you can make both drives show by setting the drive that is Offline to Online in
the Windows® Disk Management settings.
Preconditions:
a
The docking station is NOT connected to a computer.
1. Move the on/off switch ON/OFF into the position OFF.
2. Install the source drive in the bay Source.
3. Install the target drive in the bay Target.
4. Move the on/off switch ON/OFF into the position ON.
à
The indicator POWER lights up.
à The indicators Source and Target indicate that disks are connected.
5. Press and hold the button Clone for 5 seconds to start cloning.
à
The indicators 25% to 100% indicate the cloning status.
6. Wait until the indicator 100% is lit solid.
à
You have cloned the source drive to the target drive.
8 Cleaning
Important:
– Do not use aggressive cleaning agents, rubbing alcohol or other chemical solutions.
They damage the housing and can cause the product to malfunction.
– Do not immerse the product in water.
1. Disconnect the product from the power supply.
2. Let the product cool down to ambient temperature.
3. Clean the product with a dry, fibre-free cloth.
9 Disposal
This symbol must appear on any electrical and electronic equipment placed on
the EU market. This symbol indicates that this device should not be disposed of
as unsorted municipal waste at the end of its service life.
Owners of WEEE (Waste from Electrical and Electronic Equipment) shall dispose
of it separately from unsorted municipal waste. Spent batteries and accumulators,
which are not enclosed by the WEEE, as well as lamps that can be removed from
the WEEE in a non-destructive manner, must be removed by end users from the
WEEE in a non-destructive manner before it is handed over to a collection point.
Distributors of electrical and electronic equipment are legally obliged to provide free take-
back of waste. Conrad provides the following return options free of charge (more details on
our website):
■
in our Conrad offices
■
at the Conrad collection points
■
at the collection points of public waste management authorities or the collection points
set up by manufacturers or distributors within the meaning of the ElektroG
End users are responsible for deleting personal data from the WEEE to be disposed of.
It should be noted that different obligations about the return or recycling of WEEE may apply
in countries outside of Germany.
4

10 Technical data

10.1 Product
Input voltage .................................. 12 V/DC
Input current .................................. 3 A
Supported USB standards.............. max. USB3.1 Gen 1
Number of bays .............................. 2
Supported drive types..................... HDD / SSD
Supported drive interfaces.............. SATA I/II/III
Supported drive sizes..................... 6.4 cm (2.5")
Max. supported drive capacity........ 16 TB
Max. transfer speed........................ 5 Gbps
Max. cloning speed......................... limited by drive
Hot-swappable................................ Yes
System requirements...................... Windows® 7 or higher;
Operating temperature .................. 0 to +40 °C
Operating humidity ........................ 20 - 90 % RH (non-condensing)
Storage temperature ...................... -20 to +60 °C
Storage humidity ............................ 20 - 90 % RH (non-condensing)
Dimensions (W x H x D) (approx.) . 140 x 65 x 115 mm
Weight (approx.) ............................ 300 g

10.2 Power adapter

Input .............................................. 100 - 240 V/AC, 50/60 Hz
Output ............................................ 12 V/DC, 3 A
This is a publication by Conrad Electronic SE, Klaus-Conrad-Str. 1, D-92240 Hirschau (www.conrad.com).
All rights including translation reserved. Reproduction by any method (e.g. photocopying, microfilming or the capture in
electronic data processing systems) requires prior written approval from the editor. Reprinting, also in part, is prohibited.
This publication reflects the technical status at the time of printing.
Copyright by Conrad Electronic SE.
*2788198_V1_0623_jh_mh_en 27021598644155659-2 I4/O1 en
8.9 cm (3.5")
Linux Ubuntu 16.10 or higher;
MacOS 10.10 or higher;