Metabo PowerMaxx CC 12 BL Originalbetriebsanleitung Seite 18

en ENGLISH
In continuous operation, the machine
continues running if it is forced out of your
hands. Therefore, always hold the machine using
the handles provided, stand in a safe position and
concentrate.
Machines with a slide switch:
0
Switching on: push the slide switch (4) forwards.
For continuous operation, tilt it downwards
until it engages.
Switching off: press the rear end of the slide switch
(4) and release it.
8.2 Working Directions
Grinding:
Press down the machine evenly on the surface and
move back and forth so that the surface of the
workpiece does not become too hot.
Rough grinding: position the machine at an angle of
30° - 40° for the best working results.
Cut-off grinding:
Always work against the run of the disc
(see illustration). Otherwise the
machine may kick back from the cut in
an out of control manner. Guide the
machine evenly at a speed suitable for
the material being processed. Do not tilt, apply
excessive force or sway from side to side.
Sanding:
Press down the machine evenly on the surface and
move back and forth so that the surface of the
workpiece does not become too hot.
Wire brushing:
Press down the machine evenly.
9. Cleaning
Remove the battery pack from the machine before
making any adjustments, changing tools,
maintaining or cleaning.
Remove the battery pack periodically and wipe the
contact area of the battery pack and machine with a
dry cloth and remove deposits. If the battery pack
cannot be removed: see the Repairs chapter.
Particles may become deposited inside the power
tool during operation. This impairs the cooling of the
power tool. Conductive build-up can impair the
protective insulation of the power tool and create an
electrical hazard.
The power tool should be cleaned regularly, often
and thoroughly through all front and rear air vents
using a vacuum cleaner or by blowing in dry air.
Prior to this operation, separate the power tool from
the power source and wear protective glasses and
suitable dust mask. Ensure appropriate suction is
available when blowing out vents.
18
4
I
10. Troubleshooting
Electronic safety shutdown: the machine has
SHUT DOWN by itself. In the even of longer
blocking, the machine shuts down. Switch off the
machine. Switch it on again and continue to work as
normal. Try to prevent the machine from seizing.
See chapter 4.2.
Check that the spindle lock button (3) is in position
.
11. Accessories
Use only original Metabo or CAS (Cordless Alliance
System) battery packs and accessories.
Use only accessories that fulfil the requirements
and specifications listed in these operating
instructions.
Fit accessories securely. If the machine is operated
in a holder: secure the machine well. Loss of control
can cause personal injury.
Always use the suitable accessory and the
prescribed guard for the matching guard for
the application. See page 5. (Illustrations are
examples).
Application:
1 = surface grinding
2 = cut-off grinding
5 = grinding with sanding paper
Accessories:
1.1 = grinding wheel
2.1 = cut-off wheel "metal"
2.2 = cut-off wheel "masonry/concrete"
2.3 = diamond cutting disc "masonry/concrete"
2.4 = dual-purpose diamond cutting discs
(combined grinding and cutting disc)
5.1 = flap disc
prescribed guard:
Type A = cutting guard
Type B = guard for grinding
Type C = guard for grinding and cutting-off
operations (combination)
Type D = guard for cup wheel
Other accessories:
(see also www.metabo.com)
A Chargers
Best.-Nr.: 627044000 ASC 55
Best.-Nr.: 627103000 SC 30
etc.
B
Battery pack
12 V
12 V, 2.0 Ah, Li-Power..........................625406000
12 V, 4.0 Ah, LiHD................................625349000
18 V, 2.0 Ah, Li-Power..........................625596000
18 V, 4.0 Ah, LiHD................................625367000
etc.
Battery packs with different capacities. Buy
battery packs only with voltage suitable for your
power tool.