Werbung
Verfügbare Sprachen
Verfügbare Sprachen
Remove the hose stopper from the high-pressure
5
hose
6
Pull out locking hook.
Figure K
O Locking hook
@ Hoseconnection
(O High-pressure h ose
7.
Pull high-pressure
hose out of the hose connection
8.
Insert new high-pressure
hose through the two hose
guide rollers and insert into the hose connection
Observe
the
direction
of rotation
Figure L
Hose guide roller
9.
Insert the locking hook into the hose connection.
10
Check that all washers are behind the locking hook
11
Fit the hose stopper to the other end of the high
pressure hose. Distance to the end of the hose
about 1 m (to the high-pressure gun).
12
HOld
remove
Unlock the hose reel by pulling on the high-pressure
13
hose and let the high-pressure
Control the reeling speed by holding the hose.
14
Replace the cover.
Troubleshooting
A
DANGER
Risk of injury
due to inadvertently
vice
and
also
due
to electric
shock.
Switch off the device immediately
and unplug the mains
plug before performing
work.
Have electrical components
checked and repaired by
the authorised
Customer
Service.
In case of any malfunctions
not mentioned in this chap-
ter, contact the authorised
Customer Service when in
doubt or when you have been explicitly advised to do
so.
Device
does
not start
Check the power cable for damage
Check the mains voltage
•
If the device
overheats:
a Set the power switch to "O"
b
Allow
the device
to cool
for
Country
variant
Country
Electrical
connection
Voltage
Phase
Frequency
Connection
output
Degree of protection
Power protection (slow blowing)
Extension
cable,
30 m
Water
connection
Feed pressure (max )
c Set the power switch to "1"
•
Contact
faults.
Device does not reach required
Check the size of the nozzle and compare with the
required size specified in the "Technical data" sec-
tion.
Vent the device, see section "Venting the device"
Clean
Check the water supply volume and compare with
the required volume specified in the "Technical data"
section
Clean
of the
hose
reel.
Contact Customer Service if necessary.
Pump leaking
Up to 3 drops of water per minute are permissible
In case of more serious leaks, have the device
checked by Customer Service
Pump knocking
•
Check the water supply line for leaks
Vent the device, see section "Venting the device"
•
Contact Customer Service if necessary.
Allen key.
Detergent
•
Refill the foam nozzle cup
hose slowly roll up.
•
Plug a larger blender onto the suction hose.
Check
gent deposits
guide
water.
Accessories
starting
up de-
Only use original accessories
They ensure that the appliance will run fault-free and
safely.
Information
found
at www.kaercher.com
The warranty conditions
company apply in all countries. We shall remedy possi-
ble malfunctions
period free of cost, provided that a material or manufac-
turing defect is the cause. In a warranty case, please
contact your dealer (with the purchase receipt) or the
next
authorised
(See overleaf for the address)
at least
15 minutes.
Technical
data
HD6/15
HO 6115
HD
MXA
MXA
EU
CH
EU
230
230
400
3
50
50
50
kW
2,3
IPX5
IPX5
16
10
16
2
2,5
2,5
2,5
mm
MPa
English
Customer
Service
in the case
of electrical
pressure
the
sieve
in the
water
connection
the
nozzle
dosing volume
too low
the suction
hose and foam
nozzle
Remove deposits using lukewarm
and spare
parts
and original spare parts
on accessories and spare parts can be
Warranty
Issued by our relevant sales
on your appliance within the warranty
customer
service
site.
7117
HD6/
HD
71
HD
71
164
14-4
164
MXA
MXA
MXA
EU
EU
EU
230
230
400
3
50
50
50
3,3
16
16
16
2,5
2,5
2,5
for deter-
HD 81
18-4
MXA
EU
400
3
50
16
2,5
15
Werbung
