Techly ICA-PLB 546M Bedienungsanleitung Seite 10

10
The product is powered by electricity. In order to avoid burns, fire and electric shock and
make sure the safe and correct use of the system and maintain the longevity of the overall
construction and the built-in electronics, pleaseread the instruction carefully.
WARNINGS
This appliancecan be usedby childrenaged from 8 yearsand aboveif they
havebeengivensupervisionor instructionconcerninguseof the appliancein
a safeway and understand the hazardsinvolved.Childrenshall not playwith
the appliance.Cleaning and usermaintenance shall not be madeby children
without supervision.
Personswith reducedphysical,sensoryor mental capabilitiesor lack of experienceand
knowledg e mustnotusetheappliance unless they're under s upervision, understand the
hazardsInvolvedor they havebeenthoroughlyinstructedin the use of the apparatusby a
personwho is responsible for the safety of thesepersons.
Don't leavethe cordsor plug unorganized in orderto preventtrippinghazards. A nyattempts
to reconstruct the construction aren't allowed.
Do not begin the installation until you have read and understoodall the instructionsand
warningscontainedin this installationsheet. If you haveany questionsregardingany of the
instructionsor warnings,pleasecontactyour localdistributor.
This mounting bracket was designedto be installed and utilised ONLYas specified in this
manual.Improperinstallationof this product maycausedamageor seriousinjury.
This productshouldonly be installedby someonewith goodmechanical a bility who has basic
buildingexperience and fully understands this manual.
Makesurethat thesupportingsurfacewi IIsafelysupportthecombinedweightof theequipment
and all attachedhardwareandcomponents.
Always use an assistant or mechanicallifting equipment to safely lift and position the
•
equipment.
Tighten screws firmly, but do not over tighten. Over tightening can cause damage
•
totheitems, T hisgreatly reduces t heirholding power.
This productis intendedfor indooruseonly.IJSlng this productoutdoorscouldleadto product
failureand personalinjury.
Pleasedo not disassembleor change the electronic componentsof the product without
authorization.
ELECTRICAL SAFETY INSTRUCTIONS
The applianc e isonly tobeused w ith thepower supply unitrovided with the
appliance. A lterationsof the givenpowerunit arent allowe .
Never operatethe system with a damagedpower supply cord or plug. If
any parts is damaged,pleasecontact your serviceagent of purchasefor a
replacement.
Never operatethe system if it's in moist environmentor its electrical componentshas
contactwith liquids.
Don't cleanthe productwhile the poweris still connected.
Don't disassemble or replacecomponents while the power isstill connected.
Unplugthe appliancewhenthe systemisn't in use,and placethe powerplug outof children
reach.
REMOTE CONTROL USER GUIDE
A. Button functions
I. Upward/Downward movement
Pressthe " A " button,the TVmountwill moveupwardto the lowestprofile
positionagainstthe ceiling. Press the " V " button,the TVmount downward
to the maximumtilt angle position(750 by default).Pressthe "
0K
to stop the motion(Tips:clearall theobstacleswithin the rangeo motion).
2. Memory Setting
press the" E] " or " B
indicating that the current position has been saved to memory. The
" " " Ej " buttons caneach storea different p osition.
3. Recall memory
press the" " or" D
to theposition saved inthecorrisponding b utton "
4. Reset Mode
If the TVmount can't be adjustedto the highestposition(0 degreeagainstthe
ceilingsor the lowestposition (max.tilting position),unplugand re-plug the
. power Then press andhold the" G) " button for5 seconds. Mount willretract tothehighest
n, positio thatmeans t hesystem hÄeen succesfully reset.
5. Resetthe tilt range for pitched ceiling
TheTVmount is 00 a 750adjustablebydefault.Pleasereset thetilt range if you useas a pitched
ceilingTVmount.
Prepare:Resetthe system(seeInstructions on A. ButtonFunctions - 4. ResetMode).
Step 1: Press " V ", " A " and "
Step 2: Pressandhold the " " buttonuntil the unit beepsonce.Repeat t his step 5 times.The
unit will emit a long beepto indicatesuccess.
Note:Step1, 2 shouldbefinished in 2 minutes,or it will fail to reset.
Note 1: Long press" " for 5 secondsto disconnectthe devicefrom the app.
WWW.TECHLY.COM
The Modern
" button for I second untilyouheara beep,
" button andtheTVmount w ill automatically get
" or " [3
" buttonsand adjustto the properposition.
IT brand
Note 2: Theremotecontrolleris poweredby two AAAbatteries(notincluded).
B. Manual mode
In any position (but the minimumposition against the ceiling),when manuallypush up the TV
ceilingmountovera distance. T heTVceilingmountwill automaticallyreturn backto the minimum
positionagainstthe ceiling.
C.Coding of remote controller and control box
Step I: Whenthe mount is poweredon, pressthe
small button on the control box with a thin tool as
shown.The unit emits a beep.indicatingthat the
controlbox is on standb for programcoding.
Step 2: Press the ' " button on the remote
control,and the control box repeatedlybeepsfor
approximateI Osecondsindicatingthat the remotecontrol is beingprogrammed. Theprocesswill
be finishedautomaticallyuntil you can't hear a beepany longer.
Note:TheTVMountcanbe matchedwith up to 20 remotecontrollers.Toclean up the data of all
the remote controllers, pressand holdthe codematchingbuttonfor 5 secondsthenrelease.The
unit will emitstwo beepsconfirmthe successfulcleanup and vice versa.
ERROR INDICATION
I. The Buzzer constantly gives
out alarm sound: the
positioning signal"
Reset te system by
the instruction manual.
alarm soud continues,
contact us to replace the product.
REMOTE CONTROL PROBLEMS
I. Abnormal Loss Of
(Normally batteries are out of
power after 24 hours without
using the remote
Pleasecontact us to replaceremote
control.
2. Buttons on remote control
work
Please check if the batteries
power. If the problem isn't solved,
please contact us to replace remote
control.Ifthe problemis still notsolved
after the repleacement, p elasecontact usto replacethe product.
3. The insensitivity of remotecontrol (the functional distance
is less than 3m).
Pleasereplace the batteries. If the problem is still not solved,
pleasecontactus to replacethe remotecontrol.
ABNORMAL OPERATION
The TV mount can't be adjusted to
00 or 750
Pleasereset the system by following
the instructionmanual.If the problem
is still not solved,pleasecontact us to
replacethe product.
" button
CAN'T OPERATE
Pleasecheck if the power adapteris
properlyconnectedto the product. If
so, pleaseturn the poweron. Is there
is no buzzersoundor red light power
indication,pleasecheck if the power
adapter works properly.If the power
adapterdoesn'twork pleaseconctactusto replacethe poweradapter. I f the poweradapterworks
properly, b ut the TVmountdoens't work, pleasecontactus to replacethe product.
"
ABNORMAL NOISE
Pleasecontactusto replacetheproduct.
MOTORIZED
TV CEILING
error of
following
If the
please
Power
control)
don't
have
FLIP DOWN
MOUNT
2
2