Configuration Mode - Steute Rf Rx Sw868-1W Montage- Und Anschlussanleitung

RF Rx SW868/SW915/SW917/SW922-1W 24VAC/DC
Montage- und Anschlussanleitung / Funk-Empfänger
Mounting and wiring instructions / Wireless receiver
English

Configuration mode

The receiver's operating modes and the behaviour of the transmitter
are set here.
Start configuration mode:
- Press and hold the S1 button for 10 s
→ the MD LED flashes quickly (5 Hz).
- Release the S1 button
→ LED1 flashes once with a 1-second pause.
Navigation in configuration mode:
Objective Action
Current menu item
Vertical navigation Press the S1 button
briefly (< 1 s).

Horizontal Press and hold the
navigation  S1 button for at least
1 s.
Save configuration Press and hold the
S1 button for at least
1 s.
Cancel Press and hold the
S1 button for
configuration 
> 10 s or button
timeout ≥ 5 min.
Overview of configuration mode: see figure »Configuration mode«,
p. 7.
Select operation mode
These settings relate to the behaviour of the receiver. The two function
groups, relay function and transmitter function, are available for this
purpose. The relay function can be used to set the behaviour of the
switching relays. The transmitter function enables a logical link (for
several taught switches per channel), current impulse function or
wiper function.
Operation Blink code LED 1
mode
Relay functions
Standard 1 – 1 – 1
Standard, 1 – 1 – 2
inverse
output
Operation
mode
Relay
energised
Relay
energised,
inverse
output
Standard
Blinking behaviour
LED 1 flashes seve-
ral times.
Link
Latching
function
Wiper
function
Cancellation con-
firmation: LED MD
and LED 1 flash
quickly 6 times.
sWave configuration
Function
Relay energises
when actuated.
LBT (Listen Before Talk)
Relay de-energises
The radio behaviour of the sWave wireless switches is set here. LBT
when actuated,
can be switched on and off. LBT must be switched on to deliver switch
inverse output
data reliably. When LBT is on, the response time is slower by a few
signal.
milliseconds, depending on the radio load.
5 / 12
Blink code LED 1
1 – 1 – 3
1 – 1 – 4
Transmitter functions
1 – 2 – 1
AND 1 – 2 – 2 – 1
OR 1 – 2 – 2 – 2
EX-OR 1 – 2 – 2 – 3
1 – 2 – 3
600 s 1 – 2 – 4 – 7
1 s 1 – 2 – 4 – 2
2 s 1 – 2 – 4 – 3
5 s 1 – 2 – 4 – 4
120 s 1 – 2 – 4 – 5
300 s 1 – 2 – 4 – 6
600 s 1 – 2 – 4 – 7
flexible 1 – 2 – 4 – 8 – 1...600
NOTE
- If a jumper is inserted in the transmitter to set the
status signal, this jumper overwrites the setting
of the receiver.
- The manual remote control (RFHB) does not send
any status telegrams and ignores this option.
- Only battery-operated wireless switches support
the sWave configuration.
Function
Relay energises
when operating
voltage is applied.
Relay energises
when operating
voltage is applied.,
inverse output
signal.
The output takes
on the last switch
status received.
The following links
can be selected:
OR, AND, EXCLU-
SIVE-OR.
Latching function /
impulse function
Wiper function,
contact drops out
automatically after
set time.