Workplace - Fein Sts 325 R Bedienungsanleitung

Character Unit of measurement,
international
K...
2
m/s
2
m/s
h,D
m, s, kg, A, mm, V,
W, Hz, N, °C, dB,
min, m/s
For your safety.
Read all safety warnings and all
WARNING
instructions. Failure to follow the
warnings and instructions may result in electric shock,
fire and/or serious injury.
Save all warnings and instructions for future reference.
Do not use this pneumatic tool before you have
thoroughly read and completely understood this
Instruction Manual. The documents mentioned
should be kept for later use and enclosed with the
pneumatic tool, should it be passed on or sold.
Please also observe the relevant national industrial
safety regulations.
Intended use of the pneumatic tool:
Hand-guided compressed air hacksaw for commercial
use for cutting round and other shaped work pieces of
metal, plastic and cement in weather-protected envi-
ronments using the application tools and accessories
recommended by FEIN.
Safety instructions.

Workplace

Keep work area clean and tidy. Cluttered or dark work
areas invite accidents.
Do not operate the pneumatic tool in explosive atmos-
pheres, such as in the presence of flammable liquids,
gases or dusts. Pneumatic tools create sparks which can
ignite the dust or fumes.
Keep children and bystanders away while operating the
pneumatic tool. Distractions can cause you to lose con-
trol over the pneumatic tool.
Safety when handling compressed air
Clean the compressed-air supply regularly. Protect the
hose from kinks, contraction, heat, and sharp edges.
Firmly tighten the hose clamps. Have damaged hoses
and couplings repaired immediately. In case of malfunc-
tions to the air supply, the compressed-air hose can be
thrown about and lead to injury. Raised dust or chips
may cause serious eye injury.
Personal safety
Stay alert, watch what you are doing, and use common
sense when operating a pneumatic tool. Do not use a
pneumatic tool while tired or under the influence of
drugs, alcohol, or medication. A moment of inattention
while operating a pneumatic tool may result in personal
injury.
Unit of measurement,
national
2
m/s
2
m/s
m, s, kg, A, mm, V,
W, Hz, N, °C, dB,
2
min, m/s
Explanation
Uncertainty
Vibrational emission value according
(vector sum of three directions)
Mean vibrational value for sawing
Basic and derived units of measurement from
the international system of units SI.
2
Use personal protective equipment. Always wear eye
protection. Protective equipment such as dust mask,
non-skid safety shoes, hard hat, or hearing protection
used for appropriate conditions will reduce personal
injuries.
Prevent unintentional starting. Make sure that the
switch is in the "OFF" position before connecting the
pneumatic tool to the compressed-air supply. When
your finger is on the switch while carrying the pneu-
matic tool or when connecting the pneumatic tool to
the compressed-air supply while it is switched on, acci-
dents can occur.
Remove any adjustment tools or spanners before
switching on the pneumatic tool. An adjustment tool or
spanner left attached to a rotating part of a pneumatic
tool may result in personal injury.
Do not overreach. Keep proper footing and balance at
all times. This enables better control of the pneumatic
tool in unexpected situations.
Dress properly. Do not wear loose clothing or jewellery.
Keep your hair, clothing and gloves away from moving
parts. Loose clothes, jewellery or long hair can be
caught in moving parts.
If devices are provided for the connection of dust
extraction and collection facilities, ensure these are
connected and properly used. Use of dust collection can
reduce dust-related hazards.
Pneumatic tool use and care
Do not overload the pneumatic tool. Use the application
tool intended for your work. The correct pneumatic tool
will do the job better and safer at the rate for which it
is designed.
Do not use a pneumatic tool that has a defective switch.
A pneumatic tool that cannot be controlled with the
switch is dangerous and must be repaired.
Disconnect the energy supply before making any pneu-
matic tool adjustments, changing accessories, or plac-
ing the pneumatic tool aside. This safety measure
prevents accidental starting of the tool.
Store idle pneumatic tools out of the reach of children.
Do not allow persons unfamiliar with the pneumatic tool
or these instructions to operate the pneumatic tool.
Pneumatic tools are dangerous in the hands of
untrained users.
en
15