Switching On And Off; Accessories; Environmental Protection - Metabo Rsev 17-125 Originalbetriebsanleitung

en ENGLISH
8.3

Switching on and off

Always guide the machine with both hands.
Switch on first, then guide the accessory
towards the workpiece.
Avoid inadvertent starts: always switch the
tool off when the plug is removed from the
mains socket or if there has been a power cut.
The machine must not be allowed to draw in
additional dust and shavings. When switching
the machine on and off and keep it away from dust
deposits. After switching off the machine, only place
it down when the motor has come to a standstill.
In continuous operation, the machine
continues running if it is forced out of your
hands. Therefore, always hold the machine with
both hands using the handles provided, stand
securely and concentrate.
Avoid the machine swirling up or taking in dust
and chips. After switching off the machine,
only place it down when the motor has come to a
standstill.
Switching on: push the slide switch (3) forwards.
For continuous operation, tilt it downwards
until it engages.
Switching off: press the rear end of the slide switch
(3) and release it.
8.4 Working Directions
Surface grinding:
Place the machine with the entire surface of the tool
onto the workpiece. Apply moderate pressure and
move it to and fro across the surface.
Sanding:
Press down the machine evenly on the surface and
move it back and forth so that the surface of the
workpiece does not become too hot.
9. Maintenance
Prior to each use, check if there are parts
missing, worn, broken, torn or damaged. Do not
use defective or incomplete guard.
Replace brush rim (21): replace worn brush rim
for optimum extraction.
See page 3, illustration F.
Pull out worn brush rim and fully insert new brush
tim (order no. 6.26733).
10. Cleaning
Cleaning the motor: It is possible that particles
deposit inside the power tool during operation. This
impairs the cooling of the power tool.
The power tool should be cleaned regularly, often
and thoroughly through all front and rear air vents
16
3
I
0
using a vacuum cleaner or by blowing in dry air.
Prior to this operation, separate the power tool from
the power source and wear protective glasses and
a suitable dust mask. Ensure appropriate suction is
available when blowing out vents.
11. Troubleshooting
The electronic signal indicator (5) lights
up and the load speed decreases. There is
too much load on the machine! Run the
machine in idling until the electronic signal indicator
switches off.
The machine does not start.The
electronic signal indicator (5) flashes.
Restart protection is active. If the mains plug is
inserted with the machine switched on or if the
power supply is restored following an interruption,
the machine does not start up. Switch the machine
off and back on again.

12. Accessories

Use only genuine Metabo accessories.
Use only accessories that fulfil the requirements
and specifications listed in these operating
instructions.
Always use the suitable tool and the supplied
guard for the application.
Task: Surface grinding
- Tool: "Masonry/concrete" diamond cup wheel
Task: Sanding
- Tool: backing pad for sanding sheets
Work only with appropriate dust extraction: connect
an all-purpose vacuum cleaner of at least class M to
the extractor connection piece.
See www.metabo.com or the catalogue for a
complete range of accessories.
13. Repairs
Repairs to electrical tools must ONLY be
carried out by qualified electricians!
A defective mains cable must be replaced only with
a special, original mains cable from metabo
available from the Metabo service.
Contact your local Metabo representative if you
have Metabo power tools requiring repairs. For
addresses see www.metabo.com.
You can download a list of spare parts from
www.metabo.com.

14. Environmental Protection

The sanding dust generated may contain
hazardous materials: do not dispose of dust with
household waste, but at a special collection point
for hazardous waste.
Observe national regulations on environmentally
compatible disposal and on the recycling of disused
machines, packaging and accessories.