Declaration Of Conformity; Specified Conditions Of Use; General Safety Information - Metabo Rsev 17-125 Originalbetriebsanleitung

en ENGLISH
Original instructions

1. Declaration of Conformity

We declare and accept sole responsibility for
ensuring: these renovation grinders identified by
their type and serial number *1) conform to all
relevant provisions of the directives *2) and
standards *3). Technical documents for *4) - see
page 4.

2. Specified Conditions of Use

The renovation grinder is designed for surface
grinding with diamond cups, fibre grinding plates
and cling-fit backing pads.
Do not use for abrasive cutting-off operations,
roughing work, sanding, polishing or flap disc work.
Do not machine any metallic materials.
Suitable for the extraction of dusts generated during
surface grinding of mineral materials, wood,
plastics, glassfibre-reinforced plastics, paints and
residue of adhesives.
Work only with appropriate dust extraction: connect
an all-purpose vacuum cleaner (at least class M) to
the extractor connection piece (19). We
recommend using an antistatic suction hose
Ø 35 mm.
Note: The ring brush may stick when thermoelastic
materials are processed.
The machine must not be used with water.
It is suitable for commercial use in trade and
industry.
The user bears sole responsibility for any damage
caused by inappropriate use.
Generally accepted accident prevention
regulations and the enclosed safety information
must be observed.

3. General Safety Information

For your own protection and for the
protection of your power tool, pay
attention to all parts of the text that are
marked with this symbol!
WARNING – Read the operating
instructions to reduce the risk of injury.
WARNING – Read all safety warnings,
instructions, illustrations and
specifications provided with this power tool.
Failure to follow all instructions listed below may
result in electric shock, fire and/or serious injury.
Save all warnings and instructions for future
reference.
Always include these documents when passing on
your power tool.
12
4. Safety instructions for mitre
saws
4.1 Safety warnings common for grinding,
sanding:
a) This power tool is designed for surface
grinding and sanding. Read all safety
warnings, instructions, illustrations and
specifications provided with this power tool.
Failure to follow all instructions listed below may
result in electric shock, fire and/or serious injury.
b) This power tool is not suitable for routing,
grinding, wire brushing, polishing, hole cutting
or cutting-off. Operations for which the power tool
was not designed may create a hazard and cause
personal injury.
c) Do not convert this power tool to operate in a
way which is not specifically designed and
specified by the tool manufacturer. Such a
conversion may result in a loss of control and cause
serious personal injury.
d) Do not use accessories which are not
specifically designed and specified by the tool
manufacturer. Just because the accessory can be
attached to your power tool, it does not assure safe
operation.
e) The rated speed of the accessory must be at
least equal to the maximum speed marked on
the power tool. Accessories running faster than
their rated speed can break and fly apart.
f) The outside diameter and the thickness of
your accessory must be within the capacity
rating of your power tool. Incorrectly sized
accessories cannot be adequately guarded or
controlled.
g)The dimensions of the accessory mounting
must fit the dimensions of the mounting
hardware of the power tool. Accessories that do
not match the mounting hardware of the power tool
will run out of balance, vibrate excessively and may
cause loss of control.
h) Do not use a damaged accessory. Before
each use inspect the accessory such as
abrasive wheels for chips and cracks, backing
pad for cracks, tear or excess wear, wire brush
for loose or cracked wires. If power tool or
accessory is dropped, inspect for damage or
install an undamaged accessory. After
inspecting and installing an accessory,
position yourself and bystanders away from
the plane of the rotating accessory and run the
power tool at maximum no-load speed for one
minute. Damaged accessories will normally break
apart during this test time.
i) Wear personal protective equipment.
Depending on application, use face shield,
safety goggles or safety glasses. As
appropriate, wear dust mask, hearing
protectors, gloves and workshop apron
capable of stopping small abrasive or