Inhaltszusammenfassung für Axis Communications Q6010-E
Seite 1
AXIS 06010-E Network Camera Installation Guide...
Seite 2
Axis Communications AB A copy of the original declaration of conformity shall not be liable nor responsible for incidenta may be obtained from Axis Communications AB. See or consequential damages in connection with the Contact information on page 4 furnishing, performance or use of this material.
Canada Code, CSAC22.1 and National Electrical Code, ANSI/NFPA 70 This digital apparatus complies with CAN ICES-3(ClassA). The product shall be • ClassI electrical energysource (ESI) and connectedusinga shielded network cable (STP) t hat Class2 power source(PS2)rated output is properlygrounded. Cet appareil numériqueest power limited to s 100 W according to IEC/EN/UL 62368-1 conformeå...
Seite 4
Contact information Axis Communications Emdalavägen 14 223 69 Lund Sweden Tel: +46 46 272 18 00 Fax: +46 46 13 61 30 axis.com Warranty information For information about Axis' product warranty and thereto related information, go to axis.com/warranty. Support Shou d you require any technical assistance, please contact your Axis reseller.
Seite 23
AXIS Q6010-E Network Camera 2 Nm (1.48 lb ft)
Seite 24
AXIS Q6010-E Network Camera AXIS IP Utility AXIS Device Manager...
Seite 25
English • Usea limited power source (LPS) w•th a rated output power limited to S 100 W and a rated output current limited Safety information • Usea yellow/green coloredgrounding cable of at east 2.5 mm2 or 12 AWG Hazard levels Transportation ADANGER NOTICE...
Seite 26
AVIS Les piles boutons V au lithium contiennent du 1,2-diméthoxyéthane, éthyléne glycol diméthyl éther Indique une situation qui, si elle n'est pas évitée, (EGDME),CAS no 110-71-4 pourrait endommager 'appareil. Couvercle de döme Autres niveaux de message AVIS Important Veillez å ne pas rayer, endommager ou laisser Indique les informations importantes, nécessaires pour d'empreintes sur Ie couvercle du döme car cela assurer Ie bon fonctionnement de l'appareil.
Seite 27
Sicherheitsanweisungen entfernen Sie die Schutzfolie erst nachdem nstallation abgeschlossen ist. HINWEIS Säubern Sie die Kuppelabdeckung nicht, wenn Das Axis-Produkt muss unter Beachtung der diese sauber erscheint, und polieren Sie niemals ge tenden Gesetze und Bestimmungen betrieben die Oberfläche Zu häuflges Säubern kann die werden.
Seite 28
• Utilizzare solo strumenti applicabili quando si • Assicurarsi che la cupola venga installata quando il installa dispositivo Axis. Se si utilizza una forza dispositivo operativo in modo da non alterare la eccessiva con strumenti non adatti é possibile messa a fuoco causare danni al dispositivo.
Seite 29
• No coloque el objetivo de Ia cåmara apuntando hacia el sol u otras fuentes de radiaciön de alta intensidad ya que podria daftar la cåmara • La fuente de alimentaciån se enchufarå a una toma de conector instalada cerca del producto y a la que se podrå...
Seite 30
Nota (RTC) Indica informaqöesüteis que ajudama obter o måximo 3.0 V BR/CR20321) do produto. Instrucöes de seguranga AVISO O produto Axis deve ser usado em conformidade CAS#-Z-IIO 71-4) com as leis e regulamentaqöes ocais. Armazene o produto Axis em um ambiente seco F—Lh1f—...
Seite 31
• Näo limpe uma dome que pareqa impo e jamais faqa o polimento da superficie. A limpeza excessiva a3P030J1bHbIe ouncrnrem,l poderia danificar a superficie OLIMCTKM ucn0J1b3yhTe TGHb, • Para a limpeza geral de uma dome, recomenda-se CMOqeHHYK) qncT0Li BOAOi. usar sabäo ou detergente neutro näo abrasivo e Vlcnonb3YbiTe TOJ1bKO 1 1Pl,1HaAneXHOCTVl, KOTOPble sem solventes dissolvido em ågua e um pano macio...