Schweissgerät für wig und e-hand (mma) (109 Seiten)
Inhaltszusammenfassung für GYS TIG 200 DC HF FV
Seite 1
All manuals and user guides at all-guides.com FR - 2/8 – 51/56 TIG 168 DC HF EN - 9/15 – 51/56 TIG 200 DC HF FV DE - 16/22 – 51/56 ES - 23/29 – 51/56 RU - 30/36 – 51/56 NL - 37/43 –...
Seite 2
All manuals and user guides at all-guides.com DESCRIPTION Merci de votre choix ! Afin de tirer le maximum de satisfaction de votre poste, veuillez lire avec attention ce qui suit avant utilisation. Le TIG 168/200 HF DC est un poste de soudure Inverter, portable, monophasé, ventilé, pour soudage à l'électrode réfractaire (TIG) en courant continu (DC).
Seite 3
All manuals and user guides at all-guides.com Hot start ajustable Le Hot Start est réglable de 0 à 60 % dans la limite de 160A pour le TIG 168 HF DC. dans la limite de 200A en 230V, 120A en 110V pour le TIG 200 DC. 1- Cliquer et maintenir appuyé.
Seite 4
All manuals and user guides at all-guides.com Mode 4T Log Ce mode fonctionne comme le mode 4T mais lorsque vous êtes en phase de soudure une impulsion brève sur la gâchette permet de passer à un courant froid préalablement réglé (20% à 70% du courant chaud de soudage). 1- Appui gâchette : Pré-GAZ, suivi de l'amorçage.
Seite 5
All manuals and user guides at all-guides.com Réglage de l'évanouisseur (Down slope) (0 à 10 sec) Temps nécessaire pour évoluer du courant de soudage jusqu'au courant minimum. Evite les fissures et les cratères de fin de soudure. Réglage du Post GAZ (3 à 20 sec) Ce paramètre définit le temps durant lequel le gaz continue à...
Seite 6
All manuals and user guides at all-guides.com Connecteur de commande gâchette Le connecteur de commande gâchette est conçu de la manière suivante : TIG 200 TIG 168 Commun BP + Potentio. Commun Bouton courant froid Bouton courant froid ...
Seite 7
All manuals and user guides at all-guides.com FACTEUR DE MARCHE • Les postes décrits ont une caractéristique de sortie de type "courant constant". Les facteurs de marche selon la norme EN60974-1 (@ 40°C sur un cycle de 10 min.) sont indiqués dans le tableau suivant : TIG 200 (230V) TIG 168 X% @...
Seite 8
All manuals and user guides at all-guides.com - en présence de matériau inflammable ou comportant des risques d'explosion, doit toujours être soumise à l'approbation préalable d'un "responsable expert", et effectuée en présence de personnes formées pour intervenir en cas d'urgence. Les moyens techniques de protections décrits dans la Spécification Technique CEI/IEC 62081 doivent être appliquées.
Seite 9
All manuals and user guides at all-guides.com DESCRIPTION Congratulations for choosing this product, which has been designed with great care. Please read the following instructions carefully and keep this instruction manual for future reference. The TIG 168/200 HF are portable, single phase ventilated Inverter welding units to be used with non-consumable electrodes (TIG) in direct current (DC).
Seite 10
All manuals and user guides at all-guides.com Adjustable* Hot Start The 168 HF DC up to 160 A. The TIG 200FV has a limit of 200 A on 230V, and 120 A on 110V. 1- Press and hold the “Hot Start” button. 2- Select the wanted Hot Start.
Seite 11
All manuals and user guides at all-guides.com 4T Log mode This mode is the same as the 4T mode but when in welding phase, a short impulse on the trigger allows a shift to a previously set cold current (20% at 70% of hot welding current). Press trigger : pre-gas, followed by start.
Seite 12
All manuals and user guides at all-guides.com Cold current setting (low intensity) (from 20 to 70% of hot current) Selected as a percentage of hot current : the colder the current, the cooler the welding piece will stay during the welding process. Down slope setting (0 to 10 sec) Time needed to shift from welding current to minimum current.
Seite 13
All manuals and user guides at all-guides.com Recommended combinations / Electrode grinding Current (A) Ø Electrode (mm) Ø Nozzle (mm) Flow rate (Argon L/mn) = Ø wire (filler metal) 0,5-5 10-130 4-6,5 130-200 > 6.5 > 200A 12,7 To optimise the welding process, it is recommended to grind the electrode prior to welding as described in the diagram below : L = 3 x d for a low current L = d for a high current...
Seite 14
The remote control operates in TIG and MMA mode. Connector technology The TIG 200 is equipped with a female socket for a remote control. The specific 7 point male plug (GYS product ref.045699) enables connection to a manual remote control (RC) or foot pedal (PEd).
Seite 15
All manuals and user guides at all-guides.com Burns Wear protective (fire-proof) clothing (cotton, overalls or jeans). Wear protective gloves and a fire-proof apron. Ensure other people keep a safe distance from the work area and do not look directly at the welding arc.
Seite 16
All manuals and user guides at all-guides.com BESCHREIBUNG Wir freuen uns, dass Sie sich für ein Markengerät der Firma GYS entschieden haben und danken Ihnen für das entgegengebrachte Vertrauen. Bitte lesen Sie sorgfältig vor dem Erstgebrauch diese Betriebsanleitung. Der TIG 168/200 HF ist ein tragbarer, einphasiger, luftgekühlter WIG- Schweißinverter zum Gleichstromschweißen.
Seite 17
All manuals and user guides at all-guides.com Hot Start einstellbar Der Hot Start am 168 HF ist von 0 bis 60% bzw. bis max. 160A einstellbar. Der Hot Start am TIG 200 FV ist von 0 bis 60% bzw. bis max. 200A (im 230V) oder 120A (im 110V) einstellbar. 1- drücken und gedrückt halten, 2- gewünschten Hot Start Strom wählen.
Seite 18
All manuals and user guides at all-guides.com 4Takt Log Modus Dieser Modus hat die gleiche Funktion wie der 4Takt-Modus, mit dem Unterschied, dass ein kurzes Drücken des unteren Brennerwippschalters ein Umschalten auf einen vorher eingestellten, zweiten, niedrigeren Schweißstrom (20% bis 70 % des Schweißstroms) zur Folge hat. 1- oberen Brennerwippschalter drücken: Gasvorströmung beim Starten.
Seite 19
All manuals and user guides at all-guides.com Zweitstrom Einstellung (von 20 bis 70% des Schweißstroms) Die Prozentzahl des Zweitstroms gibt folgendes an: je niedriger der Prozentwert ist, desto weniger erhitzt sich das Werkstück während des Schweißens. Stromabsenkung Einstellung (0 bis 10 sec) Benötigte Zeit zum Absenken des Schweißstroms auf den niedrigsten Stromwert.
Seite 20
Potentiometerschleifer +5V Potentiometer. Potiwert 10 KΩ EINSCHALTDAUER Das GYS Schweißgerät entspricht in seiner Charakteristik einer Konstantstromquelle. Die Einschaltdauer entspricht wie unten beschrieben der Norm EN60974-1 (bei 40°C und einem 10mn Zyklus): TIG 168 TIG 200 (230V) X% @...
Seite 21
INSTANDHALTUNG / RATSCHLÄGE Die Instandhaltungsarbeiten sollten nur von qualifiziertem Fachpersonal durchgeführt werden. • Trennen Sie die Stromversorgung des GYS Geräts und warten Sie bis der Ventilator sich nicht mehr dreht. • Im Gerät sind die Spannungen sehr hoch und deshalb gefährlich.
Seite 22
Das betreffende Gerät bitte immer mit Kaufbeleg und kurzer Fehlerbeschreibung ausschließlich über den Fachhandel einschicken. Die Reparatur erfolgt erst nach Erhalt einer schriftlichen Akzeptanz (Unterschrift) des zuvor vorgelegten Kostenvoranschlags durch den Besteller. Im Fall einer Garantieleistung trägt GYS ausschließlich die Kosten für den Rückversand an den Fachhändler.
Seite 23
All manuals and user guides at all-guides.com DESCRIPCION ¡ Gracias por su elección ! Para sacar lo máximo de satisfacción de su aparato, lea atentamente lo que sigue antes el uso. El TIG 168/200 HF DC es un aparato de soldadura Inverter, portátil, monofásico y ventilado para la soldadura al electrodo refractario (TIG) en corriente continua (DC).
Seite 24
All manuals and user guides at all-guides.com Hot start ajustable* El Hot Start del TIG 168 HF DC es ajustable de 0 a 60 % en la límite de 160 A. El Hot Start del TIG 200 DC es ajustable de 0 a 60 % en la límite de 200 A en 230 V y 120 A en 110 V. 1- Clicar y mantener pulsado, 2- Seleccionar el Hot Start deseado, n.b.: la inscripción "HI"...
Seite 25
All manuals and user guides at all-guides.com Modo 4T Log Este modo funciona como el modo 4T pero cuando usted está en fase de soldaura, una pulsación breve sobre el gatillo permite pasar a una corriente fría previamente regulada (20% a 70% de la corriente caliente de soldadura). 1- Pulsar el gatillo : Pre-gas, seguido del arranque.
Seite 26
All manuals and user guides at all-guides.com Reglaje de la corriente fría (intensidad baja) (de 20% a 70% de la corriente caliente) Es el porcentaje de corriente caliente. Cuanto más la corriente fría está baja, menos la pieza va a calentar durante la soldadura.
Seite 27
All manuals and user guides at all-guides.com Conectador de mando gatillo El conectador de mando gatillo es concebido de la manera siguiente : TIG 168 TIG 200 Común común botón pulsador + Botón corriente fría potenciómetro Botón de soldadura antorcha ...
Seite 28
All manuals and user guides at all-guides.com Nb: En cas de error, desconectar su mando a distancia, el aparato indica que ahora nada está conectado: « No ». Después, conectar de nuevo el mando y rehacer la selección. Comentario: Esta elección tendrá que repetirse cada vez que se enchufará el aparato. Funcionamiento Mando a distancia manual.
Seite 29
All manuals and user guides at all-guides.com Precauciones Toda operación de soldadura : suplementarias : - en lugares con riesgos aumentados de choque eléctrico, - en lugares cerrados, - en presencia de material inflamable o con riesgos de explosión, Siempre debe ser supuesta a la autorisación previa de un "responsable experto" y hecha en presencia de personas formadas para intervenir en caso de urgencia.
Seite 30
All manuals and user guides at all-guides.com ОПИСАНИЕ Спасибо за ваш выбор ! Чтобы вы были максимально удовлетворены использованием вашего аппарата, пожалуйста, внимательно прочтите инструкцию. TIG 168/200 DC - это Инвертерный сварочный аппарат, переносной, однофазный, с вентилятором для сварки тугоплавким электродом (TIG) при постоянном токе (DC). Сварка TIG DC должна происходить в среде газа (Аргон).
Seite 31
All manuals and user guides at all-guides.com Регулируемый* Hot start Hot Start аппарата TIG 168 HF регулируется от 0 до 60 % в пределах 160 A Hot Start аппарата TIG 200 DC регулируется от 0 до 60 % в пределах 200 A при 230В и 120A при 110В 1- Нажать...
Seite 32
All manuals and user guides at all-guides.com 4-х тактный Log Этот режим работает как и 4-ч тактный, но при сварке короткое нажатие на курок позволяет пропустить предварительно отрегулированный слабый (от 20% до 70% высокого сварочного тока). 1- Нажать на курок : Подача газа, затем розжиг. Для упрощения позиционирования...
Seite 33
All manuals and user guides at all-guides.com Регулировка Продувки газа (от 3 до 20 сек) Этот параметр определяет время, в течение которого газ продолжает подаваться после затухания дуги. Таким образом деталь и электрод защищены от окисления. Наш совет : Увеличить это время если у шва темный цвет. (За...
Seite 34
All manuals and user guides at all-guides.com Коннектор для куркового управления Коннектор для куркового управления работает следующим образом : TIG 168 TIG 200 общий общий Пусковой Кнопки + кнопка холодного тока Потенциометр кнопка сварки горелкой кнопка холодного тока ...
Seite 35
All manuals and user guides at all-guides.com Nb : если вы ошиблись, отключите дистанционное управление, аппарат покажет, что больше ничего не подключено: « No ». Затем, подключите заново дистанционное управление и выберите нужный тип управления. Примечание: Этот выбор надо будет делать при каждом включении аппарата. Функционирование...
Seite 36
All manuals and user guides at all-guides.com Сварка в высоко расположенной зоне запрещена, кроме как на обезопасенных рабочих площадках. Люди, имеющие кардиостимуляторы, должны спросить совета врача перед тем, как использовать эти аппараты. Аппарат нельзя использовать для оттаивания канализаций. В режиме TIG, перемещайте газовый баллон, соблюдая все меры предосторожности, т.к. существует...
Seite 37
All manuals and user guides at all-guides.com BESCHRIJVING Hartelijk dank u voor uw keuze! Om er een maximale voldoening uit te halen, lees aandachtig wat hierop volgt. DeTIG168/200HF DCzijn draagbaar, enkele fase, geventileerde Inverter lasseneenheden om te gebruiken met nonconsumable elektroden (TIG) in gelijkstroom (DC). Bij TIG DC lassen wordt altijd een beschermgas gebruikt (Argon).
Seite 38
All manuals and user guides at all-guides.com Instelbaar Hot Start De Hot Start is instelbaar (tussen 0 en 60%) binnen de grenzen van 160A voor de TIG 168HF DC. binnen de grenzen van 200A op 230V en 120A op 110V voor TIG 200 DC. 1 - Houd de "Hot Start"...
Seite 39
All manuals and user guides at all-guides.com 4T Log Modus Deze modus is dezelfde als de 4T modus, maar wanneer in het lassen fase; met een korte impuls op de trekker kunt u verschuiven naar een eerder ingestelde koude stroom (20% tegen 70% van hot lasstroom). 1 - Druk op trekker: pre-gas, gevolgd door de start.Om positionering van de elektrode te vergemakkelijken,wordt een lage stroom van 10A verschaft, als een lichtbundel.
Seite 40
All manuals and user guides at all-guides.com Down-slope instelling(van 0 tot 10 sec) De tijd die nodig is om van de gebruikte naar de minimale lasstroom te gaan. Vermijdt de schuren en de kratervormig aan het einde van het lasproces. Post-gas instelling (van 3 tot 20 sec) Deze parameter definieert de tijd waarin het gas blijft stromen het uitsterven van de lasboog.
Seite 41
All manuals and user guides at all-guides.com Toorts controle connector Toorts controle connector is opgebouwd als volgt: TIG 200 TIG 168 GND schakelaar GND schakelaar + Potentio. Knop koude stroom Knop koude stroom Knop toorts lassen ...
Seite 42
All manuals and user guides at all-guides.com INSCHAKELDUUR • De beschreven lasapparaten hebben een uitgaande eigenschap van "constante stroom". De inschakelduur volgens de EN60974-1norm(@ 40°C op een cyclus van 10 min.) is vermeld in de onderstaande tabel: TIG 200 (230V) TIG 168 X% @ I max...
Seite 43
All manuals and user guides at all-guides.com - in de gesloten ruimtes, - in aanwezigheid van ontvlambare of explosieve materialen, moet vooraf door een "expert supervisor" worden geëvalueerd, en moet altijd uitgevoerd worden in aanwezigheid van mensen die opgeleid zijn om in te kunnen grijpen bij noodgevallen.
Seite 44
All manuals and user guides at all-guides.com DESCRIZIONE Grazie per aver scelto questo prodotto, progettato con attenzione ai bisogni dell’utente. Per favore leggere attentamente le seguenti istruzioni e tenere in luogo sicuro in modo da poterle consultare in caso di bisogno. TIG 168/200 HF sono Inverter venitilati, portatili, fase singola, progettati per essere usati con elettrodi TIG con corrente continua (DC).
Seite 45
All manuals and user guides at all-guides.com Hot Start Regolabile* Il 168 HF DC arriva fino a 160 A. TIG 200FV ha il limite dei 200 A con 230V, e 120 A con 110V. 1- Premere e rilasciare il tasto “Hot Start”. 2- Selezioanare il valore dell’Hot Start desiderato.
Seite 46
All manuals and user guides at all-guides.com E’ lo stesso del 4T, ma quando in saldatura, un breve impulsoe sul grilletto permette di tornare ad un valore di corrente fredda precedentemente impostato (20% a 70% di corrente di saldatura calda). Premere il grilletto : pre-gas, seguita dall’innesco.
Seite 47
All manuals and user guides at all-guides.com Impostazione del valore della corrente fredda (bassa intensità) (da 20 a 70% della corrente calda) Selezionata come percentuale della corrente calda: più il valore della corrente fredda è basso, e meno il pezzo si riscalderà durante la saldatura. Impostazione della diminuzione della corrente (0 a 10 sec) Tenpo necessario per passare dalla corrente di saldatura al valore minimo della corrente.
Seite 48
All manuals and user guides at all-guides.com Combinazioni consigliate / Molatura elettrodi Current (A) Ø Elettrodo (mm) Ø Ugello (mm) Flusso dell’aria (Argon = Ø filo L/mn) 0,5-5 10-130 4-6,5 130-200 > 6.5 > 200A 12,7 Per ottimizzare il prcesso di saldatura, si consiglia di molare l’elettrodo prima di saldare come descritto sotto: L = 3 x d per la corrente bassa L = d per la corrente alta Connettore torcia con grilletto...
Seite 49
Connessione TIG 200 sono dotati di una presa femmina per il commando a distanza. La spina maschio a 7 spinotti (codice GYS 045699) permette la connessione per il comando manuale a distanza (RC) o per il comando a pedale (PEd).
Seite 50
All manuals and user guides at all-guides.com Bruciature Indossare abbigliamento protettivo (ignifugo) cotone, jeans. Indossare guanti protettivi e di materiale ignifugo. Assicurarsi che le altre persone mantengano una distanza adeguata dalla zona di lavoro. Non guardare direttamente la luce dell’arco. Proteggere gli altri installando delle pareti di protezione.
Seite 51
All manuals and user guides at all-guides.com PIÈCES DE RECHANGE / SPARE PARTS /ERSATZTEILE/ PIEZAS DE RECAMBIO/ ЗАПАСНЫЕ ДЕТАЛИ / N° Cordon secteur - Power supply cord - Netzzuleitung - Cordón de alimentación - Сетевой 21492 21480 шнур - Cavo corrente Carte électronique Principale - Main Electronic Board - Hauptplatine - Tarjeta electrónica 97124C 97101C...
Seite 52
CE Kennzeichnung: 2017 DECLARACION DE CONFORMIDAD GYS atesta que los aparatos de soldadura TIG 168/200 están fabricados en conformidad con las directivas baja tensión 2006/95/CE del 12/12/2006, y las directivas compatibilidad electromecánica 2004/108/CE del 15/12/2004. Esta conformidad está establecida por el respeto a las normas EN 60974-1 de 2005, EN 50445 de 2008, EN 60974-10 de 2007.
Seite 53
All manuals and user guides at all-guides.com ICONES/SYMBOLS/ ZEICHENERKLÄRUNG/ ICONOS/ ГРАФИЧЕСКИЕ СИМВОЛЫ / ICONE Ampères - Amps - Ampere - Amperios - Ампер - Ampère Volt - Volt - Volt - Voltios - Вольт - Volt Hertz - Hertz - Hertz - Hertz - Герц - Hertz Soudage à...
Seite 54
All manuals and user guides at all-guides.com нормам. - Apparecchio conforme alle Direttive Europee. Marque de conformité EAC (Communauté économique Eurasienne) - Conformity mark EAC (Eurasian Economic Commission) - EAC-Konformitätszeichen (Eurasische Wirtschaftsgemeinschaft) - Marca de conformidad EAC (Comunidad económica euroasiática) - Маркировка соответствия EAC (Евразийское экономическое сообщество) - Marchio di conformità...
Seite 55
All manuals and user guides at all-guides.com SCHÉMA ELECTRIQUE / CIRCUIT DIAGRAM / SCHALTPLAN / SCHEMA ELETTRICO TIG 168 TIG 200 DC HF FV 55/56...
Seite 56
All manuals and user guides at all-guides.com FACADE ET BRANCHEMENT / FRONT AND CONNECTIONS / FRONTSEITE UND ANSCHLÜSSE / CARA DELANTERA Y CONEXIONES / ПЕРЕДНЯЯ ПАНЕЛЬ И ПОДКЛЮЧЕНИЕ / FRONTALE E COLLEGAMENTO Bouton de mise en marche/ veille / регулировки слабого тока TIG/ Hotstart TIG : power connection Standby button / Standby Taste / Botón MMA / Tasto di regolazione della corrente...