Panasonic EY37A2 Bedienungsanleitung Seite 11

Recalling a preset in AM/FM mode
1. Press the Source button until "AM" or "FM" is
displayed.
2. Momentarily press the required Preset button
to cause the radio to tune to one of the
stations stored in the preset memory.
FM stereo/mono ––––––––––––––––– FM
If the FM radio station being listened to has
a weak signal some hiss may be audible. It
is possible to reduce this hiss by forcing the
radio to play the station in mono rather than
stereo.
1. Press the Source button as needed to select
the FM band and tune to the desired FM
station as previously stated.
2. Press and hold Tuning control knob to enter
the menu setting.
3. Rotate the Tuning control until "FM" shows
on the display and press the Tuning control
knob to enter the setting. If the setting is ST
(stereo) press the Tuning control to switch to
MN (mono) mode to reduce the hiss. Press
the Tuning control to select the option.
Listening to music via Bluetooth
streaming –––––––––––––––––––––– BT
You need to pair your Bluetooth
the radio before you can auto-link to play/
stream Bluetooth
®
Paring creates a 'bond' so two devices can
recognize each other.
Pairing your Bluetooth
time
1. Press the Source button until "BT" is
displayed.
display and the Bluetooth
on the display.
2. Activate Bluetooth
to the device's user manual to allow the
paring procedure.
3. Press the Bluetooth
will show on the display. You can start
the search of the radio on your Bluetooth
device. Once "EY37A2" is appeared on your
Bluetooth device, press the item in your
®
Bluetooth list and it will link with the radio.
®
4. Once connected, the Bluetooth
remain steady on the display. You can now
play the music in your Bluetooth
device via the radio.
NOTE:
• If 'EY37A2' shows on your Bluetooth
device list but your device cannot connect
EY37A2.indb 11
®
device with
®
music through the radio.
device for the first
®
will be appeared on the
icon will flash
®
on your device according
®
pairing button, then
®
®
icon will
®
-enabled
®
®
- 11 -
with it, please delete the item from your
list and pair the device with the radio
again following the steps described
previously.
• The effective operation range between
the radio and the paired device is
approximately 10 meters (30 feet). Any
obstacle between the radio and the device
can reduce the operational range.
• Bluetooth connectivity performance
®
may vary depending on the connected
Bluetooth devices. Please refer to the
®
Bluetooth capabilities of your device
®
before connecting to the radio. All features
may not be supported on some paired
Bluetooth devices.
®
Playing previously-paired devices
This unit can memorize up to 8 sets of paired
devices, when the memory exceed this
amount, the earliest paired device will be
overwritten from the radio.
If your Bluetooth device already paired with
®
the unit previously, the unit will memorize
your Bluetooth device and it attempts to
®
reconnect automatically with a device in
memory which is last connected. If the last
connected device is not available, the radio
will try to connect to the second last device,
and so forth.
Erasing the paired device memory
Press and hold the Bluetooth
for approximately 7 seconds until you hear
a double tone. The radio clears all devices
from its memory and becomes discoverable.
Disconnecting your Bluetooth
Press and hold the Bluetooth
until the radio beeps to disconnect with your
Bluetooth device. The Bluetooth
®
flash on the display indicating the radio is
discoverable again for pairing.
Clock and Alarms
Setting the clock format
The clock display used in stand-by mode and
on the playing mode screens can be set to
different format. The selected format is then
also used when setting the alarms.
1. Make sure the radio is powered on. Press
and hold the Tuning control to enter the
advanced menu of the current mode.
2. Rotate the Tuning control until "TIM" shows
on the display and press the Tuning control
to enter the setting.
EN
pairing button
®
device
®
pairing button
®
icon will
®
–––––––––––––– TIM
2015-2-11 17:07:25