Inhaltszusammenfassung für Pro-Ject Audio Systems Juke Box E HiFi Set
Seite 1
Setup Guide Juke Box E HiFi Set Juke Box S2 Stereo Set...
Seite 2
Setup Guide for Installationsanleitung für Juke Box E HiFi Set Juke Box E HiFi Set Juke Box S2 Stereo Set Juke Box S2 Stereo Set...
Seite 3
Getting started: Die ersten Schritte: - Make sure you have enough space to - Stellen Sie sicher, dass genügend Platz zum Auspacken Ihres Plattenspielers unpack your turntable. vorhanden ist. - Always unpack and setup in a - Immer in einer sauberen Umgebung clean environment auspacken und aufstellen.
Seite 4
Unpack all items from Packen Sie alle Artikel the outer carton. aus dem Karton aus. a) Juke Box turntable a) Juke Box Plattenspieler b) Speaker cable b) Lautsprecherkabel d) Damp it rubber damping feet c) Damp it Dämpfungsfüße e) Speaker Box d) Speaker Box...
Seite 6
Open turntable carton and Öffnen Sie den Plattenspieler-Karton und unpack all items from accessory bag. packen Sie alle Zubehörteile aus. a) Stylus pressure gauge a) Tonarmwaage b) Batteries for remote control b) Batterien für die Fernbedienung c) Drive Belt c) Riemen d) Fabric gloves d) Stoffhandschuhe e) Adapter for 7“singles / allen key...
Seite 8
Remove the dust cover carton from the box. Entnehmen Sie die Staubschutzhaube.
Seite 9
Carefully remove the turntable protection insert. Entfernen Sie vorsichtig den Plattenspielerschutz.
Seite 10
Lift the wrapped turntable out of the box. Heben Sie den verpackten Plattenspieler aus dem Karton.
Seite 11
Unpack the power supply. Packen Sie das Netzteil aus.
Seite 12
Carefully remove the protection covering. Entfernen Sie vorsichtig den Schutz. FRAGILE! Handle with care!
Seite 13
Remove the platter protection. Entfernen Sie den Karton unter dem Plattenteller.
Seite 14
Put the drive belt on the pulley and platter. Legen Sie den Riemen um den Teller & den Pulley. Important: Make sure to have clean hands when touching the belt. Dirt 33 RPM on the belt can cause it to slip. 45 RPM Wichtig: Achten Sie beim Berühren des Riemens darauf, dass Sie mit...
Seite 15
Install the Bluetooth Antenna. Installieren Sie die Bluetooth-Antenne.
Seite 16
9 11 Unpack the dust cover and put it on the turntable. Installieren Sie die Staubschutzhaube.
Seite 17
Carefully lift the speakers out of the packaging. 9 12 Heben Sie die Lautsprecher vorsichtig aus der Verpackung.
Seite 18
Please use the supplied Damp-it rubber feet for less surface vibration. 9 13 Bitte verwenden Sie die mitgelieferten Damp-it Gummifüße.
Seite 19
Unpack the speaker cable. 9 14 9 14 9 Packen Sie die Lautsprecherkabel aus.
Seite 20
Plug the speaker cables into the turntable / connect the power cable. 9 15 Verbinden Sie die Lautsprecherkabel mit dem Plattenspieler und schließen Sie das Stromkabel an. Speaker cables left and right speaker channel Power cable Stromkabel Lautsprecheran- schlüsse linker &...
Seite 21
9 16 Connect each Speaker Box with the turntable. Verbinden Sie die Lautsprecher mit dem Plattenspieler.
Seite 22
9 17 Remove tonearm twist tie. Entfernen Sie die Tonarm-Transportsicherung.
Seite 23
9 18 Turn on the Juke Box. Schalten Sie die Juke Box ein. To switch on from Switching ON and standby or to standby (amplifier) (turntable motor) Einschalten von Standby Ein- und Ausschalten oder auf Standby des Motors des Verstärkers...
Seite 24
Control of the unit using the knob on the front. 9 19 Steuerung des Geräts über den Knopf an der Vorderseite. Standby Standby Press the knob for 3 seconds to Drücken Sie den Knopf 3 Sekunden turn the unit on. lang, um das Gerät einzuschalten.
Seite 25
Remove the needle protection cover. Entfernen Sie den Nadelschutz.
Seite 26
9 21 Make sure the tonearm lift lever is in an upright position. Stellen Sie sicher, dass der Tonarmhebel nach oben zeigt.
Seite 27
Move the tonearm over the lead in groove. Bewegen Sie den Tonarm über die Einlaufrille der Platte.
Seite 28
Move the tonearm lever down. 9 23 Bewegen Sie den Tonarmhebel nach unten.