SIZZIX Big Shot Pro Bedienungsanleitung Seite 2

1. Introduction
Machir*
for full assemblyand Operatbn-The Shot Pro Machire will Cut and embogsa
variety Of mate6alø with the entire line OfSizix dies and em"øøing tools. See
Guide 13)for
Storage
2. Machine Placement
Lift the Big Shot Prv Machine it.ø moued handholdsat the ends Ofthe Machine.
Placethe machirz on a clean. sturdy. ran-skid surface at a height
position that arecortforüblefor the Nopart af the muhlneshouldhang
over the edge of the work surface.
3. Setting Up Big Shot Pro Machine
Tod •
(2)
Lock Washer
(4)
CapCoer
(5) Extended Sliding Tray
(6) ExtendedCutting Pads 2
(7) uapter
o
4. Operating Instructions
See Die and Accessory Compatibility Tableon page 14
Five B
Using Any Size Steel-Rule Dies
l. Place a Steel-Ru le D e an
up (See Figure B).Place fabricor Othermaterialto
Place another appropriately sized Cutting Padon
a •sandwich."
2. Place sandwichon top Of the ExtendedAdapter Padin the ExtendedSliding
Tray.
3. PughSliding TrayinCoCheoæning Ofthe Big Shot Pro Machine.Keephands
from role While in
A WARNING PirEh
Md dotü•.g
md
o
and parts
not place diæ in
3mm Allen *french (Inclu&d)
(Incluåd)
QrA)
(4) Cap
Cutting pad With foam
cut ontop Of t he die.
Ofthe fabric or material to
Keep mga•s
away from contact wifi
use.
Inserting the Sliding Tray and Adapter
A WARNING
The Big Stwt Pro Machine
Use extreme
Sæk
Remove Shot pr0 machinefrom the ShippingCarton and
clean. flat. sturdy. non-skid surface. Takecare when lifting machineout Ofthe
carton, as it weighs30 (13.6
2. Remove Sliding Trayfrom bottom Ofthe carton. Place Sliding Tr4 onto Side
Rails.For cutting with Sinl:x dies. place Adapter Padin SlidingTray.
Sliding can and forth throgh the machine.
Fiwre A
Attaching the Crank Handle
l, Slip the Lock Washer(Item 2) the Screw (Item 3) and drop them into the
holein the CrankHandle (Item l).
2. Pushthe Crank Handleageembly the square roller •haft protruding
from the Big Shot Pro Machine.Insert Allen Wrenchinto
Turnclockwise(FWre A). Tighten Screwas far as possibleto ensure
maximum
3. Prz.øø the ScrewCap Cover(Item 4) in place.
o
Note the rotation Of the Crank Handle and continue
4.
direction until the sandwich has through the openingOfthe rollerå
Diegcan be passed through the rollers in either direction. from the right Or
from the left
5. Remo•æ the sandwich from the Shot Pro.Your die-cut Shapes
to usel
Pad
Figure C
Using Any Size Steel-Rule Dies with Crease Rule
A ig Similar to a regular Steel—RuleDie;
both cutting (sharp) rule and crease (blunt) rule.
Placea Steel-RuleDie onto an appropriately sized Cutting Padwith foam
up. Placepaper or Otherdesired material to beCut on top Ofthe die. Place
appropriaæly sized PremiumCreasePad(sold eeparate&) on top Of Chepaær
Or material co create a sandwich.
• If die not complete* Cut thmugh material. add
Separately) belowdie increase cutting
o
very V-E,avy.
it on a
Cap
(Item 3) to
to rotate it in the same
it
Shim (gold
material.