Nuface TRINITY Bedienungsanleitung Seite 5

WA R N I N G S (CO N T I N U E D)
• Use of controls or adjustments, or the performance of procedures other than those specified
herein, may result in injury.
• Do not disassemble the attachment as this may cause damage, malfunction, electrical shock, fire
or injury. There are no user-serviceable parts inside. Note: Disassembly voids the warranty.
P R E C AU T I O N S
The Trinity Wrinkle Reducer is designed for cosmetic use only and for individuals in good health.
If this is not the case for you, please consult your healthcare provider before use.
• If using the Trinity Wrinkle Reducer causes persistent pain or discomfort, discontinue use immediately.
• The Trinity Wrinkle Reducer is intended to be stored and used at room temperature. Do not store
Trinity Wrinkle Reducer in the sun or on a hot surface. High temperatures may be damaging. The
device should be operated, transported and stored in the manner specified in this manual. Failure
to use and maintain the device in accordance with the instructions outlined in this manual will void
the warranty.
The NuFACE Trinity Wrinkle Reducer is intended for cosmetic use on the face as described.
Any consequence resulting from misuse, application to other parts of the body or face, connection
to improper voltage sources, dirty surface, or any other improper applications is neither the
responsibility of NuFACE nor its affiliates.
G E T T I N G STA R T E D
FOLLOW THESE IMPORTANT STEPS BEFORE USING YOUR NEW ATTACHMENT.
1) Note: The Trinity Wrinkle Reducer's unique technology utilizes flashing LEDs to address facial
wrinkles. Begin treatment in a well-lit room if you find flashing lights bothersome.
2) Firmly press the release button to remove the current attachment. When fastening a new
treatment attachment, press the release button, guide the attachment in place, and then release
the button to secure the attachment to your Trinity Device.
3) The +/- keys are not active when the Trinity Wrinkle Reducer is attached. There is only one setting
for this attachment.
4) Now, test your skin to make sure you are not sensitive to light. To do so, place the Trinity Wrinkle
Reducer on your forearm for 3 minutes and then check the area. If your skin turns red and the
redness lasts for more than 2 hours, you may be sensitive to light therapy and should consult
with your healthcare provider before continuing to use the Trinity Wrinkle Reducer.
5) Before you start, remember to take a photo of your cleansed face in a well-lit room to document
your results. After your first treatment, take an after photo and repeat the photos in the same well-lit
room every 4 weeks to track your results.
D E V I C E S O U N D I N D I C AT E S
Ascending beeps Powered ON
Descending beeps Powered OFF
Dual-tone beep End of interval
Three beeps Skin not in contact
5
NF_WrinkleReducerAttachment_UserManual_Draft_042919NEW.indd 9
T R E AT M E N T A R E A S
The Trinity Wrinkle Reducer is designed to address large surface areas of the face. The following
instructions are designed to provide users with the most effective results when followed correctly.
H OW TO U S E YO U R T R I N I T Y W R I N K L E R E D U C E R
GET READY TO GIVE WRINKLES THE RED LIGHT.
1) Cleanse your face with an oil-free cleanser.
2) Remove your device from the charging cradle and turn it on by pressing the ON/OFF button.
An ascending audible beep is emitted notifying you that your device is ON, and the red LEDs will flash
rapidly 3 times. Do not touch the Trinity Wrinkle Reducer shield until the unit has finished flashing.
3) Divide the face into 7 sections (see diagram in Quick Start) and treat each section separately.
4) Place the Trinity Wrinkle Reducer in direct contact with your clean, dry skin, over the area to
be treated. Your Trinity Wrinkle Reducer has a skin sensor that will illuminate the red LEDs when
in complete contact with your skin. Press firmly enough to keep the Trinity Wrinkle Reducer in
direct contact with your skin. The device should be used on lines and wrinkles within the section,
not specifically where the number appears on the photo. Treat each section for 3 minutes until the
beep sounds.
5) If the Trinity Wrinkle Reducer is not touching the skin, your device will emit 3 beeps notifying you
to hold directly on your skin.
6) The Trinity Device will automatically shut OFF after 21 minutes indicating you are now finished
with your treatment.
Note: Do not immerse device in water at any time.
T R E AT M E N T F R E Q U E N C Y
• Use no more than 3 minutes per area, up to 21 minutes a day for the entire face.
Do not overlap areas.
• For the first 60 days, use 5 days per week.
• After 60 days, use 2-3 days per week for maintenance.
• Allow 24 hours between treatments.
R E S U LTS
Results may vary based on skin type and skin condition. It takes about 8 weeks to see the start of
the reduction in the appearance of fine lines and wrinkles. Some users see results in a shorter period
of time, while others take longer.
C A R I N G F O R YO U R T R I N I T Y W R I N K L E R E D U C E R
CLEANING
Slightly dampen a soft, lint-free cloth with water or rubbing alcohol to clean your device and
attachment. Do not immerse device in water at any time.
6
4/29/19 4:24 PM