Werbung
Verfügbare Sprachen
Verfügbare Sprachen
en
WS-PRIMER
8. SETUP OF THE GUN
CAUTION
TO SUPPLY THE SPRAY GUN USE CLEAN AIR FILTERED THROUGH AIR DRYER AND AIR FILTER.
WHEN USING THIS GUN FOR THE FIRST TIME AFTER PURCHASE, CLEAN FLUID PASSAGES
AND REMOVE RUST PREVENTIVE OIL BY SPRAYING CLEANER.
FIRMLY FIX GRAVITY CUP TO SPRAY GUN, TO AVOID THAT DISCONNECTION OF IT, CAN CAUSE
BODILY INJURY.
Flush fluid passages with a compatible cleaner.
1.
Firmly connect an air hose to air nipple G1/4" M.
2.
Firmly connect the gravity cup to fluid nipple G1/4" F.
3.
Fill the gravity cup with the previously prepared paint, adjust fluid output and as well as pattern width.
4.
9. HOW TO OPERATE
S et i nl et p r es s u r e i n t h e r a ng e 0, 5 - 2, 5 b a r ( 7 - 36 p s i ) a c c o r d i ng t o p a i nt p r o p er t i es , 2. 0 b a r ( 29 p s i ) m a x i m u m
R ec o m m end e d
p a i nt v i s c o s i t y d i f f er s a c c o r d i ng t o p a i nt p r o p er t y a n d
r ec o m m end e d .
S et t h e s p r a y d i s t a n c e f r o m
T h e g u n s h o
u l d
b e h e l d
s o
i n a s t r a i g h t a n d
h o
r i z o nt a l l i ne. A r c i ng t h e g u n c a u
10. MAINTENANCE AND INSPECTION
CAUTION
BEFORE CARRYING OUT MAINTENANCE AND INSPECTION ALWAYS OBSERVE WARNING INDICATIONS.
NEVER DAMAGE FLUID NOZZLE TIP, FLUID NEEDLE OR AIR CAP HOLES.
NEVER IMMERSE THE SPRAY GUN COMPLETELY IN LIQUIDS SUCH AS THINNER.
NEVER USE SPARE PARTS THAT ARE NOT ANEST IWATA ORIGINALS.
10.1 MANUAL CLEANING PROCEDURE
THE FLUID PASSAGES OF THE GUN, MUST BE CLEANED THOROUGHLY AFTER EACH USE,
ESPECIALLY AFTER USE WITH BI-COMPONENT PAINTS. INCOMPLETE CLEANING CAN CAUSE
DEFECTIVE PATTERN SHAPE.
NEVER USE METAL BRUSH TO CLEAN THE GUN.
NEVER SOAK AIR CAP SET (1) IN CLEANING LIQUID FOR AN EXTENDED PERIOD, even when cleaning.
D r a i n r em a i ni ng p a i nt f r o m
1.
P o u r c l e a n er
i nt o c u p .
2.
U ns c r ew a i r c a p
( 1 ) b y 2 t u r n s ,
3.
P u l l t r i g g er ( 1 5) a n d
4.
5.
L ea v e c l e a n er
f o r a f ew s e c o nd s ,
6.
R ep ea t p r o c ed u
r e a b o
R em o v e a i r c a p
( 1 ) a n d
7.
w a s t
e c l o t h .
8.
D r y
a l l
p a r t
s c o m p l e t el y a n d
10.2 AUTOMATIC CLEANING PROCEDURE
When using automatic spray gun washer, follow the instruction manual provided with it. B ef o r e c l e a ni ng , m a k e s u r e a i r i s
r el e a s e d
f r o m
a i r p a s s a g
es .
Use only a cleaner specifically designed for your spray gun washer.
Make sure that the equipment is dried immediately after cleaning.
Do not leave spray guns inside spray gun washer, after cleaning. C l e a n er
i ns i d e g u n b o
d y .
WET on WET & FILLER
t h e g u n t o t h e w o r k
p i ec e w i t h i n t h e r a n g e o f 150-250 m m
t h a t i t i s p er p end i c u l a r t o t h e s u r f a c e o f t h e w o r k p i ec e a t a l l t i m es . T h en, t h e g u n s h o u l d
s e s
s p r a y g u n a n d
c u p , i nt o a s u i t a b l e
t o a l l o
w a t o m i z i ng a i r t o b a c
m a k e s u r e, t h a t a t o m i z i ng a i r ent er s c u p .
t h en em p t y i t i nt o s u i t a b l e
v e, u nt i l s p r a y g u n i s c l e a n .
c u p f r o m
g u n, t h e n c l e a n
a p p l y s p r a y g u n l u b r i
-
G R A V I T Y S P R A Y G U N S
p a i nt i ng c o nd i t i o ns . 15 t o 23 s ec . / F o r d c u p # 4 i s
u nev en p a i nt i ng .
c o nt a i ner .
k f l u s h , f l u i d p a s s a g es o f t h e g u n.
w a s t
e c o nt a i ner .
ea c h s e c t i o n w i t h b r u s h s o a k ed w i t h c l e a ner a nd w i p e o u t w i t h
c a n t t o ea c h t h r ea d .
v a p o u r c a n d a
f o r c o m p l i a nt .
( 5 . 9 - 9. 8 i n) .
m a g e p a c k i ng s a nd c a u s e c o r r o s i o n
m o v e
5
Werbung
