Specifi Cations - Hameg Instruments Hmp4030 Handbuch

Programmable 3 Channel High Performance Power Supply HMP4030
Programmable 3 Channel High Performance Power Supply HMP4040
All data valid at 23 °C after 30 minute warm-up
Outputs
Advanced parallel and series operation: simultaneously switch on/off of
active channels via 'Output' button, common voltage- and current control
using tracking mode (individual channel linking), individual mapping of
channels which shall be affected by FuseLink overcurrent protection
(switch-off), all channels galvanically isolated and independant from pro-
tective earth
HMP4030 3 x 0...32V/ 0...10A
HMP4040 4 x 0...32V/ 0...10A
Output terminals: 4mm safety sockets frontside
Screw-type terminal rear side
(4 units per channel)
Output power: 384W max.
Compensation of lead
resistances (Sense): 1V
Overvoltage / overcurrent
protection (OVP / OCP): Adjustable for each channel
Electronic fuse: Adjustable for each channel,
combinable via FuseLink
Response time: ‹ 10ms
32V channels
Output values:
HMP4030 3 x 0...32V/0...10A, (5A at 32V, 160W max.)
I1 + I2 + I3 ≤ 25A
HMP4040 4 x 0...32V/0...10A, (5A at 32V, 160W max.)
I1 + I2 + I3 + I4 ≤ 25A
Resolution:
Voltage 1mV
‹ 1A: 0.2mA; ≥ 1A: 1mA
Current
Setting accuracy:
Voltage ‹ 0.05% + 5mV (typ. ±2mV)
Current ‹ 0.1% + 5mA (typ. ±1mA at I ‹ 500mA)
Measurement accuracy:
Voltage ‹ 0.05% + 2mV
Current ‹ 500mA: ‹ 0.05% + 0.5mA, typ. ±0.5mA
≥ 500mA: ‹ 0.05% + 2mA, typ. ±2mA
Current
Residual ripple (3Hz...100kHz):
Voltage ‹ 150μV
Current ‹ 1mA
Stabilisation at load
change (10...90%):
Voltage ‹ 0.01% + 2mV
Current ‹ 0.01% + 250μA
Stabilisation at line voltage
variation (±10%):
Voltage ‹ 0.01% + 2mV
Current ‹ 0.01% + 250μA
Entire load regulation:
(at 10%...90% load peak, ‹ 100μs
balance time to match
within 10mV U )
nom.
w w w . h a m e g . c o m
HM4030E/MAN300409/ce · Subject to changes · © HAMEG Instruments GmbH
HAMEG Instruments GmbH · Industriestr. 6 · D-63533 Mainhausen · Tel +49 (0) 6182 800 0 · Fax +49 (0) 6182 800 100 · www.hameg.com · info@hameg.com
rms
rms
Arbitrary Function easyARB (32V and 5V channels)
Parameters of points:
Number of points:
Dwell time:
Repetition rate:
Trigger:
Maximum ratings
Reverse voltage:
Reverse polarized voltage:
Max. permitted current in
case of reverse voltage:
Voltage to earth:
Miscellaneous
Temperature coefficient / °C:
Voltage
Current
Display:
Memory:
Interface:
Process time:
Protection class:
Power supply:
Mains fuse:
Power consumption:
Operating temperature:
Storage temperature:
Rel. humidity:
Dimensions (W x H x D):
Weight:
Accessories supplied: Line cord, Operating manual,
Dual-Interface USB/RS-232 (HO720), CD
Optional accessories:
HO730 Dual-Interface Ethernet/USB
HO740 Interface IEEE-488 (GPIB), galvanically isolated
HZ10S 5 x silicone test lead (measurement connection in black)
HZ10R 5 x silicone test lead (measurement connection in red)
HZ10B 5 x silicone test lead (measurement connection in blue)
HZ43 3RU 19'' Rackmount Kit
® · DQS-certified in accordance with DIN EN ISO 9001:2000, Reg.-No.: DE-071040 QM
S p e c i f i c a t i o n s
Voltage, current, time
128
10ms ... 60s
Continuously or burst mode
with 1...255 repetitions
Manually via keyboard or via Interface
33V max.
0.4V max.
5A max.
150V max.
0.01% + 2mV
0.02% + 3mA
240 x 128 Pixel LCD (full grafical)
Non volatile memory for 3 Arbitrary
functions and 10 device settings
Dual-Interface USB / RS-232 (HO720)
‹ 50ms
Safety class I (EN61010-1)
115 / 230V ± 10%; 50 / 60Hz, CAT II
Microfuse 5 x 20mm slow blow
115V: 2 x 10A
230V: 2 x 5A
550VA max.
+5°C...+40°C
-20°C...+70°C
5%...80% (non condensing)
285 x 125 x 365mm
approx. 10kg
Subject to change without notice
23