Fornetto RANGER PRO 310 Gebrauchsanweisung Seite 3

SECURING THE HOSE AND
A) Screw on hose connection
- The bbq's manifold connection is 1/4" Male Thread BSP.
- The connection between hose and regulator and the bbq should
be tightened with a spanner. Take care not to over tighten the joints.
B) Push on hose connection
NO, IS, Fl, 0K, CZ, HR, Sl, HU, TR, EE, LT, LV, PL, PT
- A universal adaptor suitable for a Push on Hose Connection
supplied within your bbq body (Fig.5).
- Attach this adaptor to the 1/4" BSP male thread as shown in (Fig.6).
- Tighten with a spanner. Take care not to over tighten the joints.
- Use appropriate jubilee clip or twin eared fastener to connect the
hose to the bbq adaptor and secure the hose/regulator connection.
- After the assembly has been secured, turn on the gas and check for
leaks. Ensure this procedure is carried out in a flame free
environment.
TESTING FOR LEAKS - DO THIS
NOTE - DO NOT test for gas leaks with an open flame. If
you smell gas, turn off at the source.
Before first use, at the beginning of each new season, or whenever a
gas cylinder is changed, you must check for gas leaks.
Do so by:
- Tum on the gas cylinder.
- Tum all gas valves on the bbq to the 'OFF
- Brush a soap solution of one part liquid detergent and one part water
to all gas connections.
- The presence of bubbles indicates a leak. Tighten or repair as
necessary.
- Under no circumstances should
leaks.
- If a gas odour is prsent and no leaks can be found, do not use the
bbq. Turn the gas off at the source, disconnect
immediately contact your bbq dealer or place of purchase for
assistance.
REGULATOR ASSEMBLY
- suit DE, AT, CH, GB (Fig.4)
(Fig.4)
- suit GB, 'E, IT, ES, FR, NL, BE, SE
(Fig.5)
(Fig.6)
BEFORE USING
position.
a naked flame be used to check
the hose and
GAS CYLINDER
- Always change over a gas cylinder away from any possible source
of ignition in a well ventilated area.
- Do not smoke whilst handling gas cylinders.
- Never store gas cylinder indoors.
- Store away from direct heat in a well ventilated
- The gas cylinder can either be positioned on the right side of the bbq
on the gas cylinder hook supplied, or alternatively
cylinder on a flat non-flammable
- Always keep the gas cylinder in an upright
- Close cylinder valve when bbq is not in use and, if available, use a
sealing plug to prevent possible leaks.
- DO not subject gas cylinder to excessive
- Do not tamper with any fitting attached to any gas cylinder. Have it
taken to the manufacturer or an authorized testing station.
- When the cylinder runs out of gas, have it refilled or swapped at an
authorized testing station. They will fill the cylinder to no more than
80% of its capacity. This allows the gas to expand with temperatures.
- Have the cylinder inspected EVERY 10 YEARS at an authorized
testing station. The date of every inspection is imprinted onto the
cylinder itself.
is
THE TYPE
There are many different sizes of gas cylinder available.
The cylinder size shown here is the maximum that should be used.
Gas cylinder capacity: max. 10.5 kg
Height of gas cylinder. max. 595 mm
Diameter of gas cylinder: max. 304 mm
YOUR BBQ
for
Location of Gas Cylinder
Place cylinder inside the cabinet. Ensure there are no kinks in the gas hose.
The maximum length of a gas hose used must be not longer than 1.0m.
SAFETY
surface.
OF GAS CYLINDER TO BE USED
Max:Ø304mm
666
6
area.
position the
position.
heat.
MAN03