Dexaplan BA 611 Bedienungsanleitung Seite 36

Preparing for first use
As determined by the automatic dialling function
(factory setting: dialling function switched on) and
the set number of dialling processes the alarm and
emergency telephone dialler dials all the stored tel-
ephone numbers in a cycle:
1st telephone number (30 sec.) - 3 sec. wait -
2nd telephone number (30 sec.) - 3 sec. wait -
3rd telephone number (30 sec.) - 3 sec. wait -
4th telephone number (30 sec.) - 3 sec. wait -
5th telephone number (30 sec.) - 3 sec. wait -
1st telephone number (30 sec.) - 3 sec. wait ....
etc.
If the person called accepts the call, he will hear an alarm
sound (even if the siren is switched off ) until the telephone
connection is automatically stopped after max. 35 seconds
by the alarm unit.
If the telephone connection of the dialling device and the
called telephone device have the features to enable the
caller display function to work then the telephone number
of the dialling device is displayed on the LC display of the
called telephone device. Even if one or more of the called
people accept the calls, all the telephone numbers (even
those who have already answered) are called for the set
number of dialling processes. The dialling cycle can only
be interrupted by disarming the device.
If the alarm and emergency telephone dialler is not dis-
armed during or after an alarm then it remains armed.
The alarm can be triggered again after the end of the si-
ren sounding process (approx. 90 seconds) or at the end
of the dialling cycle.
Disarming the alarm and emergency telephone
dialler:
Disarming with the remote control
d
Press the key
on the alarm unit
34 GB/MT
Enter the current password.
y
Press the OK key .
If appropriate, the alarm sound stops.
If appropriate, the flashing word "TRIGGER" disap-
pears.
The alarm unit sounds a pip.
The word "ARM" disappears from the LC display
The alarm and emergency telephone dialler is now
disarmed.
Note: Whilst the alarm unit is dialling a telephone
number, i.e. it is establishing a telephone connection, the
alarm and emergency telephone dialler cannot be dis-
armed using the keys on the device. The remote control
can be used to disarm the device at any time.
Switching the panic alarm On / Off:
u
Press the PANIC key on the alarm unit or the
:
"PANIC" key on the remote control.
If the alarm is triggered, the word "TRIGGER" appears
w
at the bottom of the LC display
p
The siren sounds for 30 seconds (if the siren is
switched on – see section "Switching the siren on/off")
and the programmed telephone numbers are called
(if the automatic dialling function is switched on –
see section "Switching automatic dialling on / off).
After 30 seconds the siren sounds for a second
time for 30 seconds.
To stop the alarm and dialling process, enter your
current password and press the OK key
d
the key on the remote control.
The flashing word "TRIGGER" disappears.
The alarm unit sounds a pip and the alarm is now
switched off.
Note: Whilst the alarm unit is dialling a telephone number,
i.e. it is establishing a telephone connection, the panic
alarm cannot be disarmed using the keys on the device.
The remote control can be used to disarm the device at
any time.
Switching the gong function on/off:
Set the gong On / Off switch
The gong sound sounds once.
After approx. 50 seconds delay a pip sounds. The
gong function is now activated.
If the motion detector
w
. LED
sound sounds 2 x.
To switch the gong function off again, set the gong
On / Off switch
Note: In the armed state the gong function is not activated.
Summary of the last 5 alarm events:
This function is not available when in the setting mode
nor when the alarm and emergency telephone dialler is
armed.
Press the
The times of the last 5 alarm events are displayed
one after the other.
. Wait approx. 10 seconds and the display mode auto-
matically switches off again.
Summary of the stored telephone numbers:
This function is not available when in the setting mode
nor when the alarm and emergency telephone dialler is
armed.
Press the
The stored telephone numbers are displayed one
y or press after the other.
Unassigned memory locations are shown as
"- - - - - - - - - - - - - -".
Wait approx. 10 seconds and the display mode auto-
matically switches off again.
]
on (setting "I").
{
detects some motion, the
q
illuminates once more and the gong
]
off (setting "0").
i
key repeatedly.
o
key repeatedly.