Atlas Copco LTV19 R28-10-70-ATEX Sicherheitshinweise Seite 4

Safety Information
We recommend a programme of health surveillance to detect
early symptoms which may relate to noise or vibration expo-
sure, so that management procedures can be modified to help
prevent future impairment.
If this equipment is intended for fixtured applications:
The noise emission is given as a guide to the machine-
builder. Noise and vibration emission data for the com-
plete machine should be given in the instruction manual
for the machine.
Information regarding Article 33 in REACH
The European Regulation (EU) No. 1907/2006 on Registra-
tion, Evaluation, Authorization and restriction of Chemicals
(REACH) defines among other things requirements related to
communication in the supply chain. The information require-
ment applies also to products containing so called Substances
of Very High Concern (the "Candidate List"). On 27 June
2018 lead metal (CAS nr 7439-92-1) was added to the Candi-
date List.
In accordance with the above this is to inform you that certain
mechanical components in the product may contain lead
metal. This is in compliance with current substance restriction
legislation and based on legit exemptions in the RoHS Direc-
tive (2011/65/EU). Lead metal will not leak or mutate from
the product during normal use and the concentration of lead
metal in the complete product is well below the applicable
threshold limit. Please consider local requirements on the dis-
posal of lead at product end of life.
UK DECLARATION OF CONFORMITY
We, Atlas Copco Industrial Technique AB,
SE-105 23 STOCKHOLM SWEDEN, declare
under our sole responsibility that the product
(with name, type and serial number, see front
page) is in conformity with the following UK
Regulation(s):
S.I. 2008/1597
Designated Standards applied:
EN ISO 80079-36: 2016, BS EN ISO
11148-6:2012
Authorities can request relevant technical information from:
Aleksandra Duric, Product Compliance Manager, Atlas
Copco Industrial Technique AB, SE-105 23 Stockholm Swe-
den
Stockholm, 1 September 2023
Håkan Andersson, Managing Director
Signature of issuer
Authorised Representative UK
James McAllister, General Manager
Atlas Copco Ltd
Swallowdale Lane
4 © Atlas Copco Industrial Technique AB - 9846 0761 00
Hemel Hempstead
Hertfordshire HP2 7EA
Regional Requirements
WARNING
This product can expose you to chemicals including lead,
which is known to the State of California to cause cancer
and birth defects or other reproductive harm. For more
information go to
https://www.p65warnings.ca.gov/
Safety
DO NOT DISCARD - GIVE TO USER
WARNING Read all safety warnings, instructions, il-
lustrations and specifications provided with this
power tool.
Failure to follow all instructions listed below may result
in electric shock, fire, and/or serious injury.
Save all warnings and instructions for future refer-
ence.
WARNING All locally legislated safety rules regard-
ing installation, operation and maintenance shall be
respected at all times.
Statement of Use
• For professional use only.
• This product and its accessories must not be modified in
any way.
• Do not use this product if it has been damaged.
• If the product data or hazard warning signs on the product
cease to be legible or become detached, replace without
delay.
• The product must only be installed, operated and serviced
by qualified personnel in an industrial environment.
Intended Use
This product is designed for installing and removing threaded
fasteners in wood, metal or plastic. Cable and battery tools:
Indoor use only.
No other use permitted.
The use of spare parts or accessories other than those origi-
nally supplied by the manufacturer may result in a drop in
performance and in an increased maintenance, noise level or
vibrations, and as a result, the full cancellation of the manu-
facturer's liability.
Product Specific Instructions
Installation
General Installation Safety
• Make sure that the power socket is properly fastened. Re-
place the retaining or locking pin when necessary.
LTV19 R28-10-70-ATEX