jedo DUO Bedienungsanleitung Seite 12

USER'S MANUAL
1. ASSEMBLING THE STROLLER
Releasing the lock of the folded frame is accomplished
by simultaneously pressing both buttons on the frame's
handle (Pic. 1) and pulling the handle up, when it
reaches the correct position it automatically locks in a
locking clamp, accompanied by a clearly audible "click"
sound.
2. ATTACHING AND REMOVING THE WHEELS
To remove rear wheels(Pic.2), press the button on the
inside of the frame (Pic.4) and remove the wheel along
with the axle. Repeat for the other side. To re-attach,
push the button for disengaging the wheels and push the
wheel axle into the hole in the frame. Then release the
button and pull them together until they lock.
- Install the10-inch front wheel with forks(Pic.3) by inserting
the axle of the forks to turntable, until you hear a
"click" meaning that the wheel is locked at the right
position.
The front wheels can be locked for the straight-ahead
position by turning the upper part of the turntable (Pic.
5)clockwise until they click.
To remove the wheels, press the plastic button placed on
the top of turntable (Pic. 6) and pull the wheel with the
forks to the bottom.
WARNING! The wheels are covered with a lubricant,
which may stain textiles.
3. STARTING THE PARKING DEVICE
-The truck brakes by pressing the lateral pedal of the
parking device (Pic. 7) so that the ends of the braking
rod block the wheel gears.
-The parking device is released by pulling the parking
device pedal up.
4. ASSEMBLY / REMOVAL OF THE CARRY COT.
Assemble the carry cot on the chassis by inserting the
plastic carry cot adapters, located in its lower part,
into the central locking mechanism.(Pic.8) Locking
will occur automatically. To remove the carry cot,
press buttons simultaneously on both sides of the
carry cot (Pic.9), then lift the carry cot up.
WARNING! Before use, check if the carry cot is properly
locked in the central locking mechanism.
5. INSTALLATION OF THE FOOT COVER
Put the foot cover on the carry cot and fasten using the
press-studs on the sides of the hood and the cover.
6. ADJUSTING THE BACKREST OF THE CARRY COT
The backrest in the DUO carrycot can be adjusted in
several positions.
The backrest height is adjusted by locking the
adjustment element in the selected position. (Pic.10)
7. FOLDING THE CARRY COT
To fold the carry cot, the inner material of the carry cot
must be removed to reveal the carry cots folding
mechanism hidden under it (Pic. 11), then the folding
mechanisms should be moved towards the central part of
the carry cot. To unfold the carrycot, place the folding
mechanisms in the starting position.
8. SEAT ASSEMBLY (STROLLING INSERT)
The seat assembly and disassembly is performed similar
to the carry cot, with two buttons located on both sides
of the seat. The seat can be installed in two ways - facing
forward or rearward.
WARNING! Do not carry the seat by grasping the
footrest!
WARNING! Before use, check if the seat is properly
locked in the central latch.
WARNING! Before using the stroller, always check
whether the backrest is properly locked
9. INSTALLATION / REMOVAL OF SEATS HOOD
The seat is equipped with its own hood, in order to
mount it on the seat, insert the plastic hood-
fastening elements located at the ends of the rod
(Zdj.12) into plastic connectors located on both
sides of the backrest. To remove the hood, press
the button on the hood-fastening element, then
pull the rod upwards.
10. INSTALLATION / REMOVAL RAIL
Mount the safety rail by placing the element for rail
mounting in the connectors (Pic. 13).
In order to remove the rail, press the red button located
on both sides of the rail (Pic. 13), then pull it towards
you.
11. ASSEMBLY OF FEET COVER (Seat)
Stretch cover on the seat and attach using press-studs.
12. ADJUSTING THE BACKREST OF THE SEAT.
The backrest of the seat can be set in several positions.
To lower the backrest, pull the plastic regulation element
located in the rear of the backrest, then set the correct
position. (Pic. 14)
To raise the backrest, simply push it upwards until you
reach the correct position. Locking will occur
automatically.
13. SETTING THE FOOTREST POSITION
The footrest can be adjusted in several positions. To
lower it, press the two buttons located on both sides of
the footrest and gently lower it down. (Pic. 15).
To raise the footrest, lift it upwards, it will lock
automatically.
14. ADJUSTING THE SAFETY BELT (SEAT)
The seat is equipped with five-point safety belts. To
install the belts on the seat, put the ends of the
harnesses (plastic buckle) through the holes located in
the seat backrest, under the fabric, and through the
metal handles located on the both sides of the seat.
In the same way, we mount the part of the belt located
between the legs of the child. This should be used
from the day when a baby starts to sit up unaided.
Taking the forks out from the central buckle, undo the
belts. Place the baby, adjust the length of the belts so
as they are close to baby's body, but they must not
oppress the baby. Then plug the forks of all the belts
into the central buckle (Pic. 16).
The seat has an additional crotch strap which must be
pinned to the frame with a snap. This is an additional
element and does not exempt from the application of
5-point safety belts.