Werbung
Verfügbare Sprachen
Verfügbare Sprachen
7
Install the print ribbons
a.
Lay the print ribbon carrier on its back.
b. Install the new print ribbon.
i.
With the supply roll on the right side,
and the takeup roll on the left side,
unroll a few inches of ribbon and lay
the ribbon on a clean, flat surface.
Important! Do not unroll the ribbon
beyond the black stripes on the roll.
ii.
Place the print ribbon carrier on top
of the exposed ribbon.
iii. Place the supply roll on the carrier
with the large end in the hole and
push down to snap the roll into place.
iv. Place the takeup roll on the carrier with the large end in the hole
and push down to snap the roll into place.
c.
Lay the print ribbon carrier back on its side.
d. Return the print ribbon carrier to the printer.
e. Turn the center latch clockwise to secure it.
f.
Close the printer cover.
8
Connect the power cable and power on the system
a.
Connect the power cord to the autoloader.
b. Connect the power cord from the back of the autoloader to a power outlet.
Power Cord
Important!
•
Do not power on the 3410 until you are instructed to do so.
•
Do not connect the USB cable at this time.
•
The outlet must be an earth-grounded outlet.
c.
Press the power switch at the back of the
autoloader.
The autoloader powers on.
d. Make sure the external PC is powered on.
2002544_A
9
Load discs in the system
Print Ribbon Carrier
The default bin configuration is:
•
•
Refer to the Rimage Professional 3410 and 5410N User Guide for
information on changing bin configuration.
Takeup Roll
Supply Roll
Note: If you have a Blu-ray Disc
configuration information.
10
Install the software and plug in the USB cable
Important! Do not plug in the USB cable until instructed to do so.
Note: You must have administrative privleges to install the software on
the external PC.
a.
b. Follow the on screen prompts to
c.
d. Continue to follow the on screen prompts to complete installation.
Power Switch
Load CDs in Bin 1.
Load DVDs in Bin 2.
TM
system, refer to your user guide for bin
Place the Rimage Software Suite—Network or Rimage Software
Suite—Standalone software disc in the disc drive of the external
PC.
Tip: If the software installation does not start automatically, browse
to the setup.exe file on the software disc.
complete the software installation.
When prompted, connect the USB
cable.
i.
Connect the USB cable to the
back of the autoloader.
ii.
Connect the USB cable to the
external control center (PC).
Tip: For best performance,
Rimage recommends using
USB 3.
Once installation is complete, you may be prompted to reboot your
system.
Note: After the software starts, the system begins the initialization
process. Initialization may take up to 5 minutes. During the
initialization process the lift arm moves to each recorder and the
printer. When the lift arm assembly stops moving, initialization is
complete and your system is ready to process jobs.
Copyright © 2012 Rimage
11
Test and verify
Use QuickDisc to run a 3-disc test job to verify that the system is operating
correctly.
Note: If you installed Rimage Software Suite—Network, you can now use
Rimage WebRSM to adjust the system settings. If you installed Rimage
Software Suite—Standalone, you can now use QuickDisc to adjust the system
settings
12
Register the Rimage system
Register your Rimage system to receive parts and labor covered for 1 year and
priority phone support.
Product registration and warranty activation is available at
www.rimage.com/support/warranty-registration.
13
Learn more
•
These documents are available on the Rimage Professional 3410/5410N
User Guide disc that shipped with your autoloader:
Rimage Professional 3410 and 5410N User Guide
ƒ
Rimage Advanced Setup (Networking) Guide
ƒ
Diagnostic Test Instructions
ƒ
Access these documents by placing the User Guide disc in the disc drive
of a PC.
Note: If the User Guide menu does not display automatically, browse to
the Home.htm file on the software disc.
•
For information about submitting orders to the 3410 across a network,
or to view the latest information on remote accessing, refer to the
Rimage Advanced Setup (Networking) Guide.
USB Cable
•
For information about operating and maintaining the 3410, refer to the
Rimage 3410 and 5410N User Guide.
•
For additional support and product information, go to
www.rimage.com/support.
Page 2
Werbung
