HERKULES FSG 2000 LED Bedienungsanleitung Seite 9

Anleitung FSG 2000 LED_SPK7:Anl. TPR 200_1
5. Technical data
Motor rating
Motor speed
A.c. motor 230 V ~ 50 Hz
Insulation material class
Insulation
Cut length
Jolly length
Cut height 90° max. 30 mm
Cut height 45° max. 25 mm
Cutting table:
Dimensions 570 x 385 mm
Diamond cutting wheel ø 200 x ø 25.4 mm
LED light power supply 3 x 1.5 V (AAA)
Noise emission levels
The noise emitted by this saw is measured in
accordance with EN ISO 3744; EN ISO 11201
The noise at the workplace may exceed 85 db
(A). The user will require noise protection
measures if this is the case. (Wear ear-muffs!)
With-load No-Load
operation operation
Sound pressure level L 94 dB(A) 76 dB(A)
pA
Sound power level L 107 dB(A) 89 dB(A)
WA
6. Before using for the first time
The machine must be set up so that it stands
firmly, i.e. it must be securely screwed to a work
bench, the base frame supplied in delivery, or
similar.
All covers and safety devices must be correctly
attached before the machine is used for the first
time.
The cutting wheel must rotate smoothly.
Check that the voltage on the rating plate is the
same as your supply voltage before you connect
the machine to the power supply.
7. Assembly and operation
7.1 Assembly (Fig. 1-6)
Fasten the feet (18) to the base frame (12) with
the 4 screws (19).
Turn the sub-frame upright.
Insert the two screws (37) for the trough fixture
07.12.2006
through the square holes and place the trough
(3) in the base frame (12).
Fasten the cooling water pump (13) to the mount
800 W
(38). Place the tile cutter into the trough and
3000 rpm
screw on the trough fixture (39).
Unscrew and remove the star handle screw (11)
and spacer (40) and keep them in a safe place.
Class B
Fill the trough with water until the cooling water
IP54
pump is completely immersed.
520 mm
7.2 RCD plug (Fig. 14)
520 mm
Connect the RCD plug (37) to the power supply.
Press the reset button (38) and the control lamp
(39) will begin to shine. Press the test button (40)
to check the function of the RCD plug. If
everything is working properly the control lamp
(39) will go out and the contact to the power
supply will be interrupted. The RCD plug triggers
at a fault current of 30 mA. Defective RCD plugs
must be replaced by a qualified electrician.
Press the reset key (38) again in order to be able
to start up the machine.
7.3 ON/OFF switch (Fig. 7)
To switch on, press the "1" on the ON/OFF
switch (16).
Before you begin cutting, wait until the cutting
wheel has reached maximum speed and the
cooling water pump (13) has started supplying
the cutting wheel with water.
To switch off, press the "0" on the switch (16).
7.4 90° Cutting (Fig. 8/9)
Loosen the star grip screw (27).
Set the angle stop (5) to 90° and retighten the
star grip screw (27).
Retighten the screws (28) to fasten the angle
stop (5).
Move the machine head (29) to the far end with
the handle (9).
Position the tile against the rail fence (6) on the
angle stop (5).
Switch on the tile cutting machine.
Caution: Always wait until the cooling water has
reached the cutting wheel (2) first.
Move the machine head (29) slowly and
smoothly forward through the tile with the handle
(9).
Switch off the tile cutting machine after
completion of cutting.
7.5 45° Diagonal cut (Fig. 10)
Set the angle stop (5) to 45°.
Cut as described in 7.4.
14:50 Uhr Seite 9
GB
9