HERKULES UFZS 1800 Bedienungsanleitung Seite 19

Anleitung UFZS 1800 SPK 7:Anleitung UFZS 1800 SPK 7
Wear a breathing mask
Noise emission values
Idle mode
Sound pressure level L 97,7 dB 93,2 dB
pA
Sound power level L 109,3 dB 96,3 dB
WA
The quoted values are emission values and not
necessarily reliable workplace values. Although there
is a correlation between emission and immission
levels it is impossible to draw any certain conclusions
as to the need for additional precautions. Factors
with a potential influence on the actual immission
level at the workplace include the duration of impact,
the type of room, and other sources of noise etc.,
e.g. the number of machines and other neighboring
operations. Reliable workplace values may also vary
from country to country. With this information the
user should at least be able to make a better
assessment of the dangers and risks involved.
5. Technical data
AC motor 230V - 240V
Power P S1 1500 W S6 40% 1800 W
Idle speed n
0
Cutting-off wheel Ø 250 x Ø 30 x 2.4 mm
Number of teeth
Table size 660 x 456 mm
Drag length
Cutting height max. 73 mm / 0°
50 mm / 45°
Height adjustment infinite 0 -73 mm
Tilting saw blade infinite -2° -47°
Extractor socket
Weight
Vibration
6. Before putting the machine into
operation
Unpack the bench-type circular saw and check it
for damage which may have occurred in transit.
The machine has to be set up where it can stand
firmly, e.g. on a work bench, or it must be bolted
to a strong base.
All covers and safety devices have to be
properly fitted before the machine is switched
on.
It must be possible for the saw blade to run
freely.
When working with wood that has been
processed before, watch out for foreign bodies
such as nails or screws etc.
Before you actuate the On/Off switch, make sure
that the saw blade is correctly fitted and that the
machineʼs moving parts run smoothly.
Before you connect the machine to the power
supply, make sure the data on the rating plate is
the same as that for your mains.
7. Assembly
Important! Pull out the power plug before
carrying out any maintenance, resetting or
assembly work on the cutting-off machine!
7.1 Assembly
Place the saw on a flat and firm surface.
Fasten the extractor adapter (16) with the 2
screws (35) to the back of the saw as shown in
Fig. 5.
Fit the extension pipe (50) for the lower dust
extraction device and the short extractor hose
(51) to the extractor adapter and extension pipe.
50Hz
7.2 Fitting / removing the saw blade guard (Fig.
2/3)
4300 min -1
Mount the saw blade guard (2) on the splitter (5)
so that the screw fits through the hole (44) in the
48
splitter.
Do not tighten the screw (15) too far – the blade
guard must be able to move freely.
220 mm
Fasten the extractor hose (13) to the extractor
adapter (16) and to the extractor socket of the
blade guard (2).
A suitable extractor system has to be connected
to the outlet of the extractor adapter (16).
To remove the saw blade guard, proceed in
Ø 35 mm
reverse order.
33 kg
Important!
2.07 m/s
2 The guard hood (2) must always be lowered
over the workpiece before you begin to cut.
7.3. Setting the splitter (Fig. 8/9)
Important! Pull out the power plug.
Set the blade (4) to max. cutting depth, move to
0° position and lock in place.
Remove the saw blade guard (see 7.3).
Take out the table insert (6) (see 7.5).
Slacken the fixing screw (20).
23.05.2007 11:45 Uhr Seite 19
GB
19