Werbung
Verfügbare Sprachen
Verfügbare Sprachen
6.2
Maintenance for every 50 working hours
6.2.1 Clean and adjust the spark plug
Eliminate any sediment from the electrode carbon and
insulator. Adjust the distance between the electrodes from 0.6
to 0.7 mm (thickness of three postal cards). When you locate
the spark plug, firmly press its plug.
See image 15
1
Electrode loosening controller from 0.6 to 0.7 mm
2
Spark plug cover
6.2.2 Clean the fuel filter
With a steel cable or rope extract the filter from the bole of
filled fuel and clean well with gasoline. If it is very dirty, change
the fuel filter with a new one and also clean the fuel tank.
See image 16
1
Fuel filter
6.3
Long term storage
When you do not want to use the motor for more than one
month, keep and store it according to the following procedures
to avoid any trouble or deficient functions in the starting.
1. Empty the fuel tank by letting the motor run until it has
used up all the fuel.
2. Clean the internal part of the fuel tank and the fuel filter
with clean gasoline.
3. Extract the spark plug, infuse a little amount of clean motor
oil through the hole of the spark plug. After pulling the
starter for two or three times, go back to locate the spark
plug and stop the motor in the position of compression.
4. Clean the external parts of the motor with a cloth soaked in
oil and leave the motor in a dry place away from fire heat.
6 If the motor is kept for a prolonged time with fuel in the
interior, the stain of fuel will block the fuel tube of the
carburetor or the fuel filter, which will decrease the motor's
functioning. Always empty any fuel before storing it away for
a prolonged time.
6.4
Maintenance, checks and storage
1. Before and after you use the motor, inspect its body and do
DE
Benutzerhandbuch
1
Allgemeine Warnhinweise
Lesen Sie alle Anweisungen und Warnungen sorgfältig durch,
bevor Sie dieses Produkt verwenden. Die Nichtbeachtung der
all maintenance operations if necessary. When you keep
the motor in good condition, you can ensure a more
efficient and safe operation.
2. Check if there are loose or missing parts. Tighten any loose
parts before you use the motor.
3. When you store the motor:
Completely empty the fuel tank and restart the motor to burn
the fuel left in the Carburetor and fuel tube.
–
Remove the spark plug and use an oil cape in the
interior of the spark plug hole. Later install the spark
plug again and pull the starter cable until it is tensed.
–
Inspect the air filter. Dismantle it for cleaning. Dry it
before reinstalling.
–
Keep the motor in a dry place. Protect it from dust.
Always repair any damaged parts.
6 If the motor is kept for a prolonged time without
emptying fuel tank, the sediment of the fuel will obstruct the
pass of fuel in the carburetor and in the fuel filter. It will
cause malfunction of the motor. Therefore, always make sure
that you completely empty the fuel before you store the
motor.
7 Technical specifications
Engine model
Displacement (cc)
Max power (KW/r/min)
Start system
Cooling system
Ignition system
Spark plug
Fuel mixed ratio
Fuel tank capacity (L)
Noise level dB (A )av:
ISO7917
Noise level dB (A) av:
ISO3744
Drill bit diameter (Max
deepness: 560mm)
Warnungen und Anweisungen kann zu schweren Verletzungen,
Tod oder Sachschäden führen. Überprüfen Sie vor der Montage,
ob alle Zubehörteile vollständig sind und keine Schäden
aufweisen. Falls nicht, wenden Sie sich bitte an den
1E44-5F
52
1.5/9500
Recoil start
Air – forced
CDI
MB6A
25:1 gasoline: lubricating oil
0.9
93
99
Diameter: 100 mm / 150
mm / 200 mm
DE Benutzerhandbuch
|
9
Werbung
