Werbung
Verfügbare Sprachen
Verfügbare Sprachen
2.
Press
MPH (metric: 3 KM/H, 6 KM/H, 9 KM/H, 12 KM/H) to change to the speed marked on the button.
Press "PAUSE/STOP" button, the treadmill will slow down to pause and stop running.
3.
4.
When the user holds the pulse sensors with both hands for about 5 seconds, the heartbeat rate value will
be displayed.
To stop the treadmill immediately, remove the Safety Key (No. 53), then LCD window will display "---",
5.
and the console will beep 3 times.
6.
When the set time, distance or calorie value reaches zero, the speed will gradually reduce till the treadmill
stops. The console will beep 3 times. The screen will display "End". All values will go to zero and treadmill
is now in standby state.
7.
If a value reaches the maximum value, it will reset to zero and the treadmill will stop. In manual mode, the
treadmill will stop when the time accumulates more than 99:59 min (100 min).
PROGRAM MODE
In standby state, press "P" button and the "SPEED" window will show "P01-...P12". After choosing the
1.
program, the "TIME" window will flash the pre-set time "10:00". There are 12 pre-set programs in this
system, P01-P12.
2.
Press
ranges from: 5:00-99:00.
Press "START" button, the treadmill will start running and the speed will gradually increase to the value for
3.
the first section of program (see details in the table of program parameters).
The speed changes along with the program sections. You can press
4.
press speed shortcut buttons to change to the speed marked on the button. But when it enters the next
program section, the speed will return to the pre-set speed value of that section.
Each program is divided into 20 sections, operating time for each section will be 1/20 of the set time. Each
5.
operating time period has a corresponding pre-set speed.
The console will beep 3 times when switching from one section to another.
6.
When the set time goes to zero, the console will beep 3 times and the treadmill will slow to a stop. The
7.
screen will display "End". All values go to zero and treadmill goes into standby state after 5 seconds.
At any time, if you need to stop the treadmill immediately, remove the Safety Key (No. 53). The LCD
8.
window will display "---" and the console will beep 3 times.
PROGRAM PARAMETERS
1
SPEED
3
（KM/H）
P01
SPEED
1.9
（MPH）
SPEED
3
（KM/H）
P02
SPEED
1.9
（MPH）
SPEED
5
（KM/H）
P03
SPEED
3.1
（MPH）
SPEED
5
（KM/H）
P04
SPEED
3.1
（MPH）
SPEED
5
（KM/H）
P05
SPEED
3.1
（MPH）
to adjust the speed, or press the speed shortcut buttons "1 MPH, 3 MPH, 5 MPH, 7
to adjust the time. The initial time is set to be 10 min. Only time can be set. Setting
2
3
4
5
6
4
5
5
6
5
2.5
3.1
3.1
3.7
3.1
5
6
7
7
6
3.1
3.7
4.3
4.3
3.7
10
6
11
7
12
6.2
3.7
6.8
4.3
7.4
7
8
9
9
9
4.3
5.0
5.6
5.6
5.6
8
10
11
11
10
5.0
6.2
6.8
6.8
6.2
Setup time / 20 = running time for each section
7
8
9
10
11
5
4
5
5
6
3.1
2.5
3.1
3.1
3.7
6
7
7
6
6
3.7
4.3
4.3
3.7
3.7
8
12
9
6
10
5.0
7.4
5.6
3.7
6.2
8
8
9
9
9
5.0
5.0
5.6
5.6
5.6
10
9
9
10
10
6.2
5.6
5.6
6.2
6.2
14
to adjust speed or
12
13
14
15
16
5
5
4
5
5
3.1
3.1
2.5
3.1
3.1
7
7
6
6
7
4.3
4.3
3.7
3.7
4.3
7
11
8
12
7
4.3
6.8
5.0
7.4
4.3
8
8
9
9
9
5.0
5.0
5.6
5.6
5.6
11
11
10
10
11
6.8
6.8
6.2
6.2
6.8
17
18
19
20
6
5
5
3
3.7
3.1
3.1
1.9
7
6
5
3
4.3
3.7
3.1
1.9
11
9
6
3
6.8
5.6
3.7
1.9
8
8
6
5
5.0
5.0
3.7
3.1
11
8
6
5
6.8
5.0
3.7
3.1
Werbung
