Werbung
Verfügbare Sprachen
Verfügbare Sprachen
BUTTON FUNCTION
1. "START" is the start button.
When the power is on and the safety key is well attached in the safety key seat, press this button to start
the treadmill. The default speed displayed is 0.6 MPH (metric 1.0 KM/H).
2. "PAUSE/STOP" is the pause and stop button.
When the treadmill is running, press "PAUSE/STOP" button once to pause the treadmill, and "PAUSE" will
show on the display. Time, distance, and calorie data will be automatically saved. The speed will go to zero.
Press "PAUSE/STOP" button again to stop the treadmill and all data will be cleared to zero.
3. "P" is the PROGRAM selection button.
In standby state, press to select different running programs from "0:00", "P1-P2-P3-P4-P5-P6-P7-P8-P9-
P10-P11-P12-U01-U02-U03-FAT".
"0:00" is the manual program. "P01-...P12" is the pre-set programs. "U01-...U03" is the user program. "FAT"
is the constitution detection function program. Manual mode is the default mode. The default speed is 0.6
MPH (metric 1.0KM/H).
4. "M" is the MODE selection button.
5. In setting state, press
When the treadmill is running, press to increase or decrease the speed. Value increases or decreases in
increment of 0.1 MPH (0.1 KM/H). After holding for more than 0.5 seconds, automatically continuous
acceleration and deceleration will be realized.
6. SPEED SHORTCUT BUTTONS: 1MPH, 3MPH, 5MPH, 7MPH (metric: 3KM/H, 6KM/H, 9KM/H, 12KM/H)
Press fast select 1MPH, 3MPH, 5MPH or 7MPH buttons when the treadmill is running.
SET UP COUNTDOWN MODE (MANUAL MODE)
1. Turn on the treadmill. The treadmill is in standby mode. Press "M" button to select time countdown mode,
calorie countdown mode or distance countdown mode. Press "START" button to start the treadmill.
2. To set countdown mode
In standby mode, press the "M" button to enter the time countdown mode. The "TIME" window will
a.
display and flash "15:00". Set countdown time by pressing
99:00. Value is in increment of 1:00. Press "START" button and the treadmill will start operating after 3
seconds of countdown. If you do not press "START" button and you press "M" button again, the time
value you set will be cleared and treadmill will go into distance countdown mode.
In the time countdown mode, press the "M" button to enter distance countdown mode. The "DIS."
b.
window will display and flash "1.00". Set the distance by pressing
range: 0.50-99.9. The value is in increment of 0.1
will start operating after 3 seconds of countdown. If you do not press "START" button and you press
"M" button again, the distance value you set will be cleared and treadmill will go into calorie countdown
mode.
In the distance countdown mode, press the "M" button to enter calorie countdown mode. The "CAL."
c.
window will display and flash "50.0". Set the calorie by pressing
10.0-999 KCAL. Value increases in increment of 1 KCAL. Press "START" button and the treadmill will
start operating after 3 seconds of countdown. If you do not press "START" button and you press "M"
button again, the calorie value you set will be cleared and treadmill will go into standby mode.
After the value is set in one of the three countdown modes, press "START" button and the treadmill will
d.
start operating after 3 seconds of countdown. Press
shortcut buttons to change to the speed marked on the button. Press "PAUSE/STOP" button once to
pause the treadmill.
OPERATIONS DURING THE EXERCISE
Press "START" button, the console will beep, and the treadmill will start operating after 3 seconds of
1.
countdown, the speed window shows the countdown. The initial speed is 0.6 MPH (metric: 1.0 KM/H).
to increase or decrease the set value.
MILE/KM.
13
. Time setting range 5:00-
. Distance setting
Press "START" button and the treadmill
. Calorie setting range
to adjust speed or press speed
Werbung
