Sthor 82120 Bedienungsanleitung Seite 9

PRODUCT OVERVIEW
The cordless compressor is a device that allows for infl ating tyres or other objects, e.g., balls or mattresses with compressed air.
The battery power supply increases the mobility of the product. The correct, reliable, and safe operation of the device depends
on its proper use, therefore:
Read the entire instructions manual before the fi rst use of the appliance, and keep it for future reference.
The supplier shall not be held liable for any damage resulting from failure to observe the safety regulations and recommendations
specifi ed in this manual.
PRODUCT ACCESSORIES
The factory packaging should contain: cordless compressor, USB charging cable, adapter for infl ating.
TECHNICAL DATA
Parameter
Part No.
Rated voltage
Rated current
Rated pressure
Infl ating capacity
Hose length
Battery type
Rated battery voltage
Battery capacity
Charging time
SAFETY INSTRUCTIONS
Learn how to use the tool. Do not start working or charging before reading the instructions manual. Following the guidelines con-
tained in the instructions manual reduces the risk of injury, electric shock or fi re. Observe the maximum pressure of the infl ated
products. Use a pressure gauge (built-in or separate) to control the pressure inside the infl ated product. Exceeding the maximum
pressure may cause damage to the infl ated product or even its rupture. Rupturing the product can cause serious injuries. Period-
ically check that the readings of the pressure gauge built into the tool match those of the calibrated pressure gauge. Check the
tool for damage before each use. If you notice any cracks, abrasions or other damage, do not use the tool until the defects are
removed. Check the infl ation hose for damage. If abrasions, cracks or air leaks of the insulation are discovered, stop using the
damaged hose and replace it with a new hose before continuing work. Never bend or twist the hose during operation. Bending the
hose can reduce its inside diameter even to the point where the air fl ow stops. This can lead to damage to the hose or even to its
rupture, which can result in serious injuries. Bending and twisting the hose also speeds up hose wear. Never carry the tool holding
it by the hose. Do not overtension the hose during operation. Do not use the device as a blow gun, artifi cial respiration device,
for spraying any substance or any other application not described in the instructions manual. Never point the air stream towards
yourself, other people or animals. Do not use your fi nger or any other part of the body to check if the device is pumping air. Make
sure the device is switched off before connecting the adapter to the hose and the device itself to the product to be infl ated. The
device is not intended to be used by children. Do not operate the device continuously for more than 10 minutes. After this time,
stop work and allow the device to cool down completely for at least 15 minutes. The further operation may result in overheating of
the device and its damage. It can also cause fi re or electric shock.
PRODUCT OPERATION
Preparing for operation
Unpack the product by removing all packaging components. Depending on the type of valve in the product to be infl ated, an
adapter can be used, which must be screwed in
the hose connection. The hose without an adapter is designed to infl ate Schrader valves, the so-called car valves. The supplied
conical adapters allow you to infl ate mattresses and other products equipped with a soft socket without thread. A thin adapter, the
so-called needle, allows for infl ating balls.
Position the hose end lever so that it is aligned with the tip. Slide the tip onto the valve or insert the adapter into it, then turn the
lever so that it is perpendicular to the tip.
The device has a storage compartment for unused infl ating adapters.
O R I G I N A L
EN
Unit
[V DC]
[A]
[MPa / bar / PSI]
[l/min]
[cm]
[VDC]
[Ah]
[h]
I N S T R U C T I O N S
Value
82120
5
1
0.69/6.9/100
25
40
Li-Ion
7.4
2.0
4-6
9