Denon DCD-1520 Bedienungsanleitung Seite 8

(5) Clearing the Program
e The entire program is cleared when the PROG/DIRECT button is
pressed again. The program is also cleared when the ( & opens
CLOSE) button is pressed.
e if the PROG/DIRECT button is pressed during programmed play, the
program is cleared and playback continues normally through to the last
track on the disc.
NOTES
e If programming is done in the play or pause mode, the track
currently playing is programmed at the first position. Other
tracks can be added to the program, but the number of
programmed tracks and the playing time will not be displayed.
Direct search is not possible during programmed play. If the
number buttons are pressed, that track is added to the end of the
program.
Programming is possible with the disc holder open. Track
numbers greater than the number of tracks recorded on the disc
can be programmed, but will be automatically cleared before
playback begins.
The remaining time per track will only be displayed for track
numbers 1 through 20.
The total program time and remaining program time are not
displayed if tracks greater than track number 20 are prog-
rammed.
@e Repeating playback of all tracks 0.0.0... csssscsesetcessseseeeeee Repeat All
@ Press the repeat ail button (ALL).
@ Press the play button ( »-PLAY).
e Pressing the repeat all tracks button (ALL), is displayed.
e Steps © and @ above may be reversed.
e To cancel repeat playback of all tracks, press the repeat all button (ALL)
once more.
e Pressing the repeat all button (ALL) during programmed playback,
playback of the tracks entered into the memory will be repeated.
7] Repeating a Single Track ..........ssssessssenssssssesseereneeteeees 1-track Repeat
e Press this button if you want to hear a track repeatedly.
Press 1-track repeat button (1)
The track is repeated continuously.
e If the 1-track repeat button (1) is pressed during playback of a disc
containing 20 tracks or less, the [REPEAT ] indicator lights, the number
of that track lights on the calendar and that track is played repeatedly.
The 1-track repeat function is possible if there are more than 20 tracks
on the disc, in which case only the [REPEAT | indicator lights and none
of the numbers on the calendar light.
*
e If the 1-track repeat button (1) is pressed in the stop mode, track
number 1 lights on the calendar, the indicator lights, and it
becomes possible to repeat only one track. To start, press the ( » PLAY)
button.
e Tocancel 1-track repeat, press the 1-track repeat button (1) once again.
Normal playback will resume, with the normal indicators lit.
(8) Playing a desired time or
e With this function you can specify the starting time and/or ending time
in seconds, aliowing playback of a very specific section of a track.
In the Stop Mode
e Specifying the starting time
@ Press the TIME SEARCH button. The indicator will
flash on the display, and the TRACK display will read "--".
@ Use the number buttons to set in order the track number and the time
{minutes and seconds).
Example: Starting from 2 minutes 34 seconds into track 3
Press the folowing buttons in order: (TIME SEARCH_], [0], 3), [0],
2], Bl, 4.
NOTE: If a track number or time not on the disc is set, the unit will
return to the mode it was in before the first buttons were pressed.
@® Press the { ® PLAY) button to begin playback from the specified time.
e Specifying the ending time
The ending time can be set before pressing the play button while the
(CTIMESEARCH ] indicator is flashing using the following procedure:
@® Press the TIME SEARCH button. The indicator will
stop flashing and the TRACK display will read "--".
® Use the number buttons to set in order the track number and the time
(minutes and seconds).
NOTE: It is not possible to set an ending time at a point before (or the
same as) the starting time.
© After specifying the ending time, press the { ® PLAY) button to begin
repeated playback between the two specified points. (A-B repeat by
specifying the time)
In the Play Mode
@ When the TIME SEARCH button is pressed, the current track number
and time (minutes and seconds) are stored in the memory and the
indicator begins flashing.
@ When the ( ® PLAY) button is pressed, playback starts from the starting
point stored in the memory.
To start playback over from the specified point, press the ( ®» PLAY)
button again.
@ If the TIME SEARCH button is pressed again, the ending time is stored
in the memory, the indicator stops flashing, and the
interval between the starting point and ending point is played
repeatedly. (A-B repeat)
To cancel the time search function, press one of the following buttons:
(1) PROGRAM/DIRECT
{2) DIRECT (on remote control unit)
(3) OPEN/CLOSE
NOTE:
e if the search function is used after a track number and time (minutes
and seconds) are specified with the disc holder open and no disc set,
playback will start from the beginning of the first track on the disc.
e if atime over the time on the disc is specfied, playback will start from
the beginning of the track following the specified track.
(9) Pausing playback at any POint ...........cscccssssceeeessnesservsereeseessees
interval ..
( ] PAUSE)
e Playback can be temporarily halted and then continued from the same
point in the track.
1. Press the pause button (Il PAUSE) during playback.
2. To continue playback, press the play button ( » PLAY) or the pause
button (Il PAUSE) once more.