Werbung
OPERATION
PREPARATION
1. CHECKING
CONNECTIONS
e
Make sure that all the connections are proper by referring
to the back panel. (Fig. 2~3)
@
Check the polarity (positive and negative) of connections,
and the directivity of stereo separation (right cord to right
channel terminal, and left cord to left channel terminal).
e
Check the directivity of pin cord connection.
2. SETTING
OF EACH
KNOB
e
Turn the volume
control knob counterclockwise, to "0".
e
Set the rotary knob to "flat".
e
Set the LOUDNESS
switch to "OFF".
After checking the above items, turn on the power, the amplifier is
set in the ready mode
in a few seconds.
PLAYING A RECORD
1. Set the INPUT SELECTOR
switch to "PHONO".
2. Operate the turntable and play the record.
3. Turn the volume and tone controls to yield an appropriate
volume
and sound
quality.
PLAYBACK OF CD PLAYER (1)
1. Set the INPUT SELECTOR
switch to "CD".
2. Operate the CD player.
3. Turn the volume and tone controls to yield an appropriate
volume
and sound quality.
RECEPTION
OF RADIO PROGRAMS
1. Set the INPUT SELECTOR
switch to "TUNER".
2. Operate the tuner to receive a radio program.
3. Turn the volume and tone controls to yield an appropriate
volume and sound quality.
PLAYBACK OF CD PLAYER (2)
1. Set the CD DIRECT switch to "ON"
position.
2. Operate the CD player.
3. Turn the volume
and tone controls to yield an appropriate
volume and sound quality.
CONNECTIONS OF AUDIO EQUIPMENT TO AUX-1, AUX-2 TER-
MINALS
1. Set the INPUT
SELECTOR
switch to "AUX-1"
or "AUX-2"
Position.
2. Operate the Audio equipment
Systems.
3. Turn the volume
and tone controls to yield an appropriate
volume
and soundquality.
PLAYBACK WITH TAPE DECK
Set the MONITOR/COPY switch to "TAPE-1/1>2" or "TAPE-2 / 2
b1" for playback.
ENGLISH
RECORDING
WITH TAPE DECK
When
recording from a music source as turntable, tuner or CD
player, the source can be selected with INPUT SELECTOR switch.
When
MONITOR/COPY
switch
is in "SOURCE",
the program
source signal is supplied simultaneously to TAPE REC terminals.
Signals from the source
are directly recorded
on a tape deck
independent of amplifier volume control.
Do not turn MONITOR/COPY
switch during recording.
e COPYING
FROM
ONE TAPE TO ANOTHER
To copy from tape deck 1 to 2, set MONITOR/COPY switch to
TAPE-1 / 1>2.
To copy from tape deck 2 to 1, set MONITOR/COPY switch to
TAPE-2 / 2>1.
While the tape is being copied, it is not possible to listen to
another program source from speakers. But in this case, it is
possible to listen to source
selected
by CD
DIRECT
from
speakers.
The CD DIRECT terminals are exclusively for playback, and
cannot
be used for recording.
e MONITORING
THE RECORDING
A recording in progress can be monitored if a tape deck with
three individual heads for recording and playback is used. A
tape deck in which
a common head is used for both recording
and playback cannot be used to monitor
recording. Set the
MONITOR/COPY
knob to Tape-1 or Tape-2 to correspond to
the tape deck that is being used for the recording. Use the
TAPE
MONITOR
switch
to switch
between
the
recording
monitor and the program
source.
CAUTION
Protective Circuit
This set is equipped with a high speed protctive circuit. This
circuit protects the internal circuitry from
damage due to
large currents
flowing when
the speaker jacks are not
completely connected or when an output is generated by a
short circuit. This protective circuit's operation cuts off the
output to the speakers. In such a case, be sure to turn the
power to the set off and check the connections
to the
speakers. Then turn the power on again. After muting for
several seconds, the set will operate normally.
Werbung
