Product Familiarisation; Intended Use - Silverline Air Cut-Off Tool Anleitung

GB
k) Position the supply hose clear of the spinning accessory. If you lose control, the hose
may be cut or snagged and your hand or arm may be pulled into the spinning accessory.
l) Never lay the power tool down until the accessory has come to a complete stop. The
spinning accessory may grab the surface and pull the power tool out of your control.
m) Wheels must be used only for recommended applications. For example: do not
grind with the side of the cut-off wheel. Abrasive cut-off wheels are intended for
peripheral grinding; side forces applied to these wheels may cause them to shatter.
n) Always use undamaged wheel flanges that are of correct size and shape for your
selected wheel. Proper wheel flanges support the wheel, thus reducing the possibility of
wheel breakage. Flanges for cut-off wheels may be different from grinding wheel flanges.
o) Ensure the air supply pressure does not exceed the maximum operating pressure
of the tool. Exceeding the pressure limit of the tool may cause erratic and unpredictable
operation, leading to tool damage or serious injury.
p) The operator must ensure there are no bystanders within the vicinity. Bystanders are
at risk of harm from flying debris and harmful gases produced from cutting operations.
q) Do not use the cut-off tool in a potentially explosive environment. Working with
certain materials that produce a large concentration of dust can make the environment
potentially explosive. Always ensure a sufficient dust extraction system is present when
in use.
r) In the event the energy supply is interrupted, release the start/stop mechanism, and
any switch locking device. This will prevent unintentional tool start-up if energy supply
is reconnected.
s) Always use blotters during disc installation (if provided by the manufacturer).
Blotters are specifically designed to dampen forces exerted between the spindle and disc.
Failure to use, or improper use of, the provided blotters will promote premature or abrupt
failure of the accessory.
t) Keep the cutting guard in place and in good condition at all times. Inspect the
condition of the cutting guard regularly, ensuring it is correctly installed and in good
condition. If the guard shows prominent defects, discard and replace.
Note: Internal grinding may not require a guard, providing the workpiece encloses the
abrasive accessory.
u) Before use, inspect the condition and installation of the spindle and gas supply
connecting components. Do not use the tool if the spindle or gas supply connection
points show signs of damage or fatigue.
Additional Safety Warnings
Specific for Abrasive Cutting-Off
Operations
a) Do not 'jam' the cut-off wheel or apply excessive pressure. Do not attempt to
make an excessive depth of cut. Overstressing the wheel increases the loading and
susceptibility to twisting or binding of the wheel in the cut, and also the possibility of
kickback or wheel breakage.
b) When the wheel is binding or when interrupting a cut for any reason, shut off the
power tool and hold the power tool motionless until the wheel comes to a complete
stop. Never attempt to remove the cut-off wheel from the cut while the wheel
is in motion otherwise kickback may occur. Investigate and take corrective action
to eliminate the cause of wheel binding.
c) Do not restart the cutting operation in the workpiece. Check the cutting accessory for
damage and allow the wheel to reach full speed before carefully re-entering the cut.
The wheel may bind, walk up or kickback if the power tool is restarted in the workpiece.
d) Support panels or any oversized workpiece to minimise the risk of wheel pinching
and kickback. Large workpieces tend to sag under their own weight. Supports must be
placed under the workpiece near the line of cut and near the edge of the workpiece on
both sides of the wheel
e) Use extra caution when making a 'pocket cut' into existing walls or other blind
areas. The protruding wheel may cut gas or water pipes, electrical wiring or objects that can
cause kickback.
6

Product Familiarisation

1 Body / Handle
2 Guard
3 Spindle
4 Bolt & Washer
5 Cutting Disc (not supplied)
6 5mm Hex Key
7 14mm Spanner
8 Safety Catch
9 Speed Control
10 Quick Connector

Intended Use

• Rotating cut-off tool, powered by compressed air from a compressor, for cutting of metal
(mainly thin sheet metal, nuts/bolts, car bodywork etc.).
Unpacking Your Tool
• Carefully unpack and inspect your tool. Fully familiarise yourself with all its features and
functions
• Ensure that all parts of the tool are present and in good condition. If any parts are missing
or damaged, have such parts replaced before attempting to use this tool
Before Use
Fitting the quick connector
Note: This tool is supplied with two different male airline quick connectors:
EQ-4 – commonly used in Europe
EN-6 – mainly used in the UK
EQ-4
Europe
• Please choose the connector that is compatible with the airline system you are using, and
install as outlined below:
1. Apply some PTFE tape (not included) to the screw threads of the Quick Connector (10).
This will help to maintain an air-tight seal
Note: Apply PTFE tape tightly and in a clockwise direction, so it does not come off when the
thread is screwed into the tool.
2. Remove the protective plug from the air inlet
3. Using a spanner (not included) screw the quick connector into the air inlet located at the
base of the handle
4. Connect to airline, pressurise carefully and carry out a leak check (e.g. by spraying small
amounts of soapy water on to the outside of the connectors)
• Air lines fitted with matching female quick connectors will now be a push fit to the tool
EN-6
UK