SOLIS FLEXI TEMP KETTLE Kurzanleitung Seite 17

• Do not use abrasive chemical cleaning agents such as
ammonia, acid or acetone when cleaning the appliance. This
can damage the appliance.
CO N T E N T S
V
Please check the contents of the package:
1× FLEXI TEMP KETTLE
1× Power base
A P P L I A N C E D E S C R I P T I O N ( S E E I M AG E A )
V
Opening button
1
Spout
2
Limescale filter
3
Lid
4
Kettle
5
Water level indicator
6
CO N T R O L B U T TO N S ( S E E I M AG E B )
V
Display
r
Temperature indicator
t
Keep warm indicator
y
Tea mode indicator
u
Text display
i
I N S TA L L AT I O N
V
Uncoil the power cable e.
1.
Place the power base
2. on a stable and flat as well as a heat and moisture resistant surface. Make
8
sure the power cable runs through the power cable recess w.
e
Plug the power plug
3. into a power outlet.
e
4. Place the kettle filled with water onto the power base 8. The appliance beeps for 2 seconds
5
and the display lights up.
r
B E F O R E F I R S T U S E
V
1. Boil two full kettles of water (chapter Boiling water).
2. Discard the boiled water.
B O I L I N G WAT E R
V
Avoid spillage on the power plug and the power base.
6
Press the opening button to open the lid 4.
1.
1
Fill the kettle
2. with 0.5 – 1.8 litres of water.
5
Close the lid 4.
3.
Place the kettle onto the power base 8. The appliance beeps for 2 seconds and the display
4.
5
lights up.
28
Covered heating element
7
Power base
8
Control elements with display
9
Handle
q
Power cable recess
w
Power cable and plug
e
Selection button
o
Keep warm button
p
Silent mode indicator
a
Power button
s
Push the selection button
5.
temperature indicator
If none of the buttons have been pressed within 6 seconds, the display shows the current water
4
temperature.
6. Press the power button
the temperature indicator
If the current temperature of the water is higher than the desired temperature, the heating process
4
does not start.
7. If desired, press the keep warm button
warm function. The keep warm button
up.
To cancel the heating process, press the power button again. The power button light switches off.
4
To cancel the keep warm mode, press the keep warm button again. The keep warm button light
4
switches off and the keep warm indicator switches off.
The appliance beeps 3 times when the process is finished. The power button light switches off. When
the keep warm function is activated the power button light starts blinking. The keep warm function
automatically switches off after 30 minutes.
U S I N G T H E T E A P R E - S E T S
V
1. Follow step 1-4 from chapter Boiling water.
2. Press and hold the keep warm button
The tea mode indicator
3. Push the selection button
The temperature indicator
the text display i.
If none of the buttons have been pressed within 6 seconds, the display shows the current water
4
temperature.
Tea variety
GYOKURO
SHINCHA
SENCHA
BANCHA
WHITE
GREEN
MATCHA
BLACK
HERBAL
OOLONG
4. Follow step 6-7 from chapter Boiling water.
When the heating process is done, the text display shows, instead of the tea variety, the
4
recommended brew time for the selected tea type. This is only information and not a timer function.
r
upwards or downwards to select the desired temperature. The
o
shows the desired temperature.
t
to start heating the water. The power button
s
shows the current water temperature.
t
after the heating process has started to enable the keep
p
and the keep warm indicator
p
for 2 seconds to activate the tea mode.
p
lights up on the display r.
u
upwards or downwards to select the desired tea preset.
o
shows the desired temperature and the tea variety is shown at
t
Water temperature Recommended brewing time
50 ˚C 2 minutes 30 seconds
55 ˚C 2 minutes
60 ˚C 2 minutes
65 ˚C 2 minutes
70 ˚C 9 minutes
75 ˚C 3 minutes
80 ˚C 1 minute
85 ˚C 4 minutes
90 ˚C 5 minutes
95 ˚C 6 minutes
lights up and
s
on the display light
y
29