AEG 8060 D Montage- Und Gebrauchsanweisungen Seite 5

ENGLISH
DESCRIPTION
This appliance consists of a hood and a telescopic flue which must be applied to the upper part of the hood in order to cover
the draft pipe.The appliancecan be a filtering versionone, a ductingversion one or with an externaimotor
E n the Filtering version (Fig.I), the air and vapoursconveyedby the applianceare depuratedby charcoalfilters and
recirculated a round theroom through thesideventing ductsoftheflue.ATTENTION. When usingthefiltering version, t wo
charcoal filters must be installed plus an air switch. Positioned in the upper part of the flue, this allows the air to be
recirculatedthroughoutthe room (Fig.IA). In the Ducting version (Fig.2),cookingvapours and odoursare conveyed
straightoutside byadisposal duct whichpassesthroughthe wall/ce;ling Useof charcoa* filtersisthereforeunnecessary
In the versgon with an External motor (Fig.3).the appliancemust be connectedto an ducting apparatus/motorwhich
workson its ownusing the applianceas a unionfor the air to be scavenged Use only motors proposed in the original
catalogue.
INSTALLATION
Removethe anti-grease filters before proceedingwith the assembly instructions This will makethe appliance
easierto handle.To removethe anti-greasefilters (Fig. 4): this is carriedout by pushingthe relativecatch inwardsand
turning it downwardsuntilit disengagesfrom the supporls_Proceedwiththese instructionsin reversewhen refittingthe
filters.
Wall fixing with brackets : Make all the necessary holes on the wall using the relative boring template. Apply the
supplied brackets to the wall using the relative screws and screw anchors (Fig. 5). Before installing the hood, check that
the bracket fixing screws (Fig.5A) have been sufficiently slackened to allow the hood itself to be fitted in place.
Now fit on the hood using the relative rectangular slots situated at the rear of the appliance (Fig. 5). Since these coupling
slots are dimensionally larger than the brackets, the hor:zontal position of the appliance can be adjusted by sliding to the
right or left in order to align the equipment. The appliance can be regulated in height by means ofthe relative bracket adjuster
screws (Fig.5B)_Oncehavingregulatedthe equipment, f ix everythinginplacebytighteningscrewsA (Fig5) andinserting
safety screws C (Fig. 5)
Installation with the rear panel : Therear metalpanelmustbe fixed tc the wal Inthe upperpart ofthe hob (Fig.6)
Restthe lower edgeof the panelbehindthe hob andfix the upperedge tothe wallby meansofthe two holesin the panel
itself,insertingthe suppliedscrewsandscrewanchors(Fig.6A).Theapplianceshouldbe fixedtothe rearpanelinthe same
way aswalifixing, usingthe suppliedhood bracketsandthe screwsand screw anchorssuppliedwiththe panel(Fig.6B).
Fixing the decorative pipe : The following operations are essential for assembly: — Install the wiring system within
the decorative flue. —Prepare the air venting hole if your appliance is to be installed in the ducting version or in the version
with an external motor.
In the Ducting version and in the version with an External motor ,to get optima' conditions the air venting pipe should:
—be as short as possible. —have the lowest number ot bends (max bende angle: 900). —be made of material approved
by locat authorities (according to the State). — have its inner side as regular and smooth as possible.
It is moreover recommended to avoid drastic changes of ppe cross section (recomrnended diameter: 150 mm).
Usingthe suppliedscrewsand screwanchors,fix the upperflue bearing bracketto the ceilingand/orwall, checking
that it is a!igned with the hood (Fig. 7). Prepare the decorative flues, remembering that their final position must be that
illustrated in Fig8. The air disposal gratings In the fi\tering version must be positioned in the upper part. For the ducting
version turn upside down the upper flue so that the air disposal gratings are downwards.
Ducting version and version with an external motor Adjust the flue height and fix the relattve screws (Fig8). Connect the
hood flange to the outlet on the wall/ceiling by means of a suitable pipe
Concerning the version with external motor only (Fig. 9) make the electrical connection between the hood and the external
motor by means of the proper terminal board: take off the cable clamp A and the cover B of the wiring junction box. Fix the
connection cable of the motor onto the terminat board C. Reassemble the cable clamp A and the cover B of the junction
box. The other end of the cabie must be fixed onto the terminal
Make the electrical connection of the hood by means of the power supply cable. Insen the decorative flue, fixing it at the
top and bottom through h01es A and B (Fig. 10).
Filtering version : Fix the switch fitting (Fig. 11) to the upper flue using the relative screws. Connect a suitable hose to the
switch fitting. Fix the decorative flue to the ceiling bracket by means of the relative screws B (Fig. 10). Keeping the lower
flue temporarify raised, connect the draft pipe to the hood flange, Make the electrical connection of the hood by means of
the power supply cable. Allow the decorative flue to Eowerin position and fix it to the flange support by means of supplied
screws A (Fig. 10).
OPERATION
The hoods are provided with the following type of controls:
Controls of Fig. 12: A = light switch. B first speed motor ON/OFF switch. C = second speed switch. D = third speed
switch. E = warning light
Controls of Fig. 13; Switch A . LIGHT. position O: light off; position 1. light on. Cursor B: MOTOR SPEED: used
board of the external motor.
to regulate the operative speed of the motor. Switch C: MOTOR position O: motor off, position I: motor on. Warning
light D: indicates motor operation.
Particular care must be paid to the anti-grease filters which must be periodically cleaned in relation to use (at least
once every two months). Remove the anti-grease filters and wash them using neutral detergent.
When using the filtering version of the appliance, the charcoal filters must be changed according to use (Fig. 14),
usually every six months. Remove the anti-g rease filters rotating them and replace them rotating into the opposite direcuon.
Light : If the light bulbs need changing, sacken the light cover by disconnecting the screw and remove the bulb itself
(Fig. 15). Replace with a bulb of the same type
To changethe rectangular halogen bulbs open the coverand removethe bu*bwithout touchingit with bare
hands (Fig. 16). Replace with a bulb of the same type