RAVAK FRESIA Kurzanleitung Seite 2

FRESIA
Depending on the type of installation
either one or two side panels, or it can be built-in and surrounded
INSTALLATION OF THE
1. The bathtub should only be installed into a completely finished and tiled bathroom with prepared plumbing. Ifthe
wall tile does not come down to floor level, it must be finished at least 150mm below the upper edge of the tub
(picture 2)
2. If the bathtub is to be built-in, the inside of the surrounding
touches the outer edge of the tub ( with a maximum tolerance
edge of the tub (see detailed pic. I, detail B-B). Remember! before fully enclosing the bathtub, leave an opening
in one wall for access to plumbing and siphon. Aceramic tile with magnets or a small door can cover the opening.
3. The water mains can be either 3/4" or 1/2" in diameter.
pipe should be 800mm above the floor and in an appropriate
tub mounted taps, install the outlet pipes in an area appropriate
(pic. 2)
4. The drain pipe is 50mm in diameter. It should be installed near the bathtub drain so as not to interfere with the
supporting legs (pic. 2)
B I Mounting procedure
5. During the entire installation,
6. Turn the bathtub upside down, and place the cardboard and styrofoam packaging on the corners of the tub so that
the rim of the tub and the raised headrest will not be damaged
7. Measure the metal legs of the support according to picture
in such a way so as not to interfere with the supporting
holes in the support, which allows the support to be turned around.
mark the spots where the holes will be drilled.
8. With the enclosed 3mm diameter drill bit, drill holes in the marked areas to a depth of 1Omm.
9. Assemble the support with legs and fasten it to the bottom of the bathtub (pic. 4)
10. By rotating the plastic shoes, adjust the tub with feet to a height of 61 Omm
II. Place the tub into position
enclosure.
12. When the tub is level in both directions, tighten the nuts on the feet
13. On the floor, outline the position for the siphon opening
14. On the tiled wall mark the true height of the upper edge of the bathtub. It must be 61Omm above the floor with
a tolerance of 5mm in either direction (pic.2).
15. Carefully remove the bathtub and place it aside.
16. Place the clips 55mm under the upper edge of the tub (555 mm above floor level).
should be 8mm in diameter (pic. 1)
17. Attach the holders with the4x40mm
18. We recommend the bathtub be fitted with the RAVAK complete drain kit (pic. 5) which may be purchased at the
same time as the tub. Prepare a 40mm drainage pipe for connection
19. Mount the drain to the bathtub according to the instructions
20. Before finally installing the bathtub, place some putty into the holders and slide the perpendicular
to the wall (picl detail A-A)
21. Complete the installation and siphon connection
22. Seal the spaces between the bathtub and the tiled supporting walls.
C 1 MOUNTING
When installing
panel.
MAINTENANCE, CLEANING,
If you want your bathtub to reliably serve you for a long time, please follow these recommendations
- after each use, clean the bathtub with a liquid cleaner and a soft cloth. Never use any abrasive pastes, dissolvents, acetone or detergents and desinfectants,
that contain chlorine.
- fill the tub first with cold, and then with increasingly
- repair leaky water taps without delay
- the surface of the tub can be damaged with thinners, solvents, nail polish, and polish remover
- hot things such as cigarettes or a curling iron can also damage the surface of the tub
- water scale can be removed with a mixture of water and vinegar, superficial scratches can be removed with polishing compounds
We recommend the use of the RAVAK SERIES of speciality
shower frames, enamel and acrylic bathtubs, washbasins
anti-fungal effects
The manufacturer offers a 10 year guarantee
company and that the bathtub is only used for the personal hygiene of adults and children.
In the case of misuse, or if the bathtub is mounted without supporting legs in a built-in enclosure, the guarantee is not valid
The manufacturer reserves the right to change the price, technical parameters or other facts without a prior notice and shall bear no responsibility for the printing errors.
into the bathroom, the bathtub can be enclosed
BATHTUB
For water taps mounted on the wall, the head for the water
area for proper water flow into the tub. With standard
for a built-in bathtub
leave the protective foil on the bathtub and work with caution
wall.
and if necessary, rotate the shoes to adjust the tub to the correct
bolts (pic. 1 detailed A-A)
THE PLASTIC
a bathtub with a surrounding
GUARANTEE
warmer water.
chemicals:
and water taps;
on all bathtubs, on the condition
with a front panel and with
with ceramic tile.
A1 Constructional
wall must follow the outline of the bathtub so that it
of 20mm), and it must be 2 - 3 mm lower than the cut
for mounting the taps in the correct place on the tub
3. According to the type of installation,
Also, take advantage of the asymmetrically
On the reinforced part of the bottom of the tub,
The openings
to the siphon.
given in the package
PANEL WITH THE PANEL
plastic panel, follow the mounting
RAVAK CLEANER
RAVAK DISINFECTANT
that the product is installed
CONTENTS
Metal support 700mm
readiness
2 Plastic leg M12
3 Clip
4. Dowel
5 Bolt for dowe
Bolt ø 5.5x 16mm
6
7 Drill bit Ø3mm
8 Washer
9. Threaded
10. Nut
All acrylic
be permanently
supporting
is the
which
legs.
move the legs
placed
a minimum
between
surrounding
can
silicon
height in the
bathtub.
Use a stop when drilling so that
the acrylic on the bottom of the
for the dowels
bathtub will not be damaged.
edge of the tub
KIT
instructions enclosed
is used to remove old and dried on debris from glass surfaces,
a special cleaning agent with outstanding
by a professional
OF MOUNTING
KIT - SUPPORT
2 pc
6 pc
Ø 8mm diameter 4 pc
Ø 4x40mm 4 pc
8 pc
1 pc
diameter
4 pc
6 pc
rod M12x125
18 pc
M12
ATTENTION!
bathtubs must never
built-in. The
part of the bathtub
reinforced bottom, on
are fitted adjustable
There should be
space of 2-3mm
the bathtub and the
tiles. This space
be filled with putty or
after installation of the
(Pic. 1 -detail B-B).
ATTENTION
with the
germicidal and
serviceman or