Werbung
Common Operating Procedures
\ select the next control mode.
}
Loud Indicator
4 To emphasize bass/treble at low/
medium volume levels
@ Press the LOUD button for at least 2 sec-
onds to switch on the loud feature. The bass
and treble characteristics will be emphas-
ized
when
listening
at low
or medium
volume
levels.
("LOUD"
indicator
will be
1 First time use
Turn the ignition key to oN (ACC) and press
the power switch.
==
itluminated.}
\
| @ Press the LOUD button again for at least 2
2 To adjust the volume
\
seconds to turn off the loud function.
Press " A" audio contro! to increase the vol-
ume level.
Pi
ENTE
i
H
d
th
A
a
" Me - audio
control
to
decrease
the
5 To change the audio mode
" WEL" and level indicator ("2" + - "32°) will be
Each time this button is pressed, the
( >)seiect audio mode will change in the follow-
illuminated.
:
2 ) ee
ing sequence;
3
.
BASS
» TREBLE
-» BALANCE
To turn down the volume instantly
t
1
@ Press the ATT button. Volume will decrease
VOLUME
"~
FADER
|
to about 1/10 of its previous ievel. ~ Udi"
and level indicator will blink.
|
1
®@ To return to the previous volume level, press,
i
this button again.
|
H
When a control mode is selected but no operation is made within five seconds, the display will return \
to the normal operation (volume adjustment) mode. In such a case, press the SELECT button again to
Sensor Tone On/Off Switch
The sensor tone can be switched on and off. The sensor tone can be heard confirming that a control
button has been pressed.
To activate the sensor tone;
Press
the SELECT
button
for more
than
2 seconds.
The
display pane! will show
" BEE 2" and changes
toh OTE,
|
sanctpibinnetaatices
After that the display panel will return to the normal (previous-mode) display.
| @ seer @ Press the SELECT button until the BASS
Common Operating Procedures (conta)
m Coment GERD
a mee
uot
ae
| ee
inte) c=)
|
Ot
30
|
us a
CW mrcxrmon A)
JTACKy aR
a)
i
DP37_-SOUND MEMORY
TUNE/SEEK
6 To adjust the bass and treble
i 7 To adjust the left/right balance
(& »seect
@ Press the SELECT button until the BAL-
(TRE)
mode
is selected.
"BASS
ANCE mode is selected. " #41" will be
( TPE") will be itluminated.
illuminated.
_~
@Press the " A" audio control to increase
i
JA.
@ Press the "/\"
audio control to shift the
the bass/treble response.
|
sound volume to the right speakers.
~—
@ Press the * V " audio control to shift the
sound volume to the left speakers. The
balance level indicator ("3)"-"} 5") will be
'
illuminated.
~~
@Press
the
"V""
audio
control
to !
decrease the bass/treble response. The
bass/treble level indicator ("—15" - "{9")
will be illuminated.
8 To adjust the front/rear balance
«_»»setect @ Press the SELECT button unti! the FADER mode is selected. "4" will be illuminated.
~~
@Press the
"A" audio control to shift the sound volume to the front speakers.
© Press the "Vv" audio control to shift the sound volume to the rear speakers. The fader level indicator ("C
"."35") will be illuminated.
Most-Recent Memory:
@ This unit is designed for the volume level to be memorized automatically in its respective functions (AM band, FM
band, CD player). tt means when a desired volume level for each function has been set, which will be stored
respectively in memory even if any selection is made among the functions. Therefore, this feature enables you free
from the trouble of resetting each volume along with the function selection.
@ When the power is switched off, the unit will retain al! function settings last heard when the unit is turned off and
automatically retums to those settings the next time the unit is turned on.
Note: This unit is equipped with anti-volume-biast circuit which serves as an automatic volume level adjuster so that
you will not be deafened with sudden loud volume. This system works like this. When the ATT button was switched
off and the next time the unit is turned on again, the volume level will automatically be adjusted to a certain volume
| degree, and then the volume level will gradually go back to its previous level prior to switching off the unit.
aAVS3SAL
Werbung
