Seite 1
JX3-MIX2 Multifunktionales Erweiterungsmodul Jetter AG Kontakte: Gräterstraße 2 E-Mail - Vertrieb: sales@jetter.de D-71642 Ludwigsburg E-Mail - Hotline: hotline@jetter.de Germany Telefon - Hotline: +49(0)7141/2550- Installationsanleitung Version 1.10 Artikel-Nr.: 60876765 März 2012 / Printed in Germany Laden Sie die Betriebsanleitung von www.jetter.de unter Support >...
Seite 2
Konfiguration Das Modul JX3-MIX2 ist nur direkt anschließbar an ein weiteres JX3-Modul. Das Modul wird über einen Buskopf, ein JX3-PS1 oder über einen JC-3xx mit Spannung versorgt. Montage Schritt 1 Schalten Sie zur Montage bzw. Demontage alle JX3-Module der JX3-Station spannungslos.
Seite 3
LEDs leuchtet Logikversorgung des grün: Moduls ok leuchtet rot: Kommunikation zum Buskopf bzw. JC-3xx nicht aktiv leuchtet rot: Hardware-Fehler leuchtet rot: Software-Fehler blinkt kurz Betriebssystem ist nicht rot: gültig; Update durchführen blinken rot: Betriebssystem-Update aktiv leuchtet Status der A, B gelb Zählereingänge: Log.
Seite 4
Anschlussbeschreibung X61 Klemmpunkt Digitale Signale X61.CNTA Zählereingang A X61.CNTB Zählereingang B CNTB STEP Schrittmotor-Ausgang X61.STEP "STEP", Open-Drain X61.DIR Schrittmotor-Ausgang "DIR", Open-Drain X61.0V Bezugspotenzial für digitale SHLD und analoge Signale Klemmpunkt Analoge Signale X61.AI1 Analoger Eingang 1 X61.AI2 Analoger Eingang 2 X61.AI3 Analoger Eingang 3 X61.AO1...
Seite 7
+49(0)7141/2550- Installation Instructions Revision 1.10 Item # 60876765 March 2012 / Printed in Germany The user manual can be downloaded from www.jetter.de at Support > Downloads. Scope of Delivery 10000887 JX3-MIX2 60869252 10-pin connector, spring cage technology 60870410 Keying pins...
Seite 8
Configuration The JX3-MIX2 module can only be directly connected to another JX3 module. The module is supplied with power by a bus head, a JX3-PS1, or a JC-3xx. Mounting, Step 1: For mounting, respectively disassembling, de-energize all JX3 modules of the JX3 station.
Seite 9
LEDs Green, lit: Lodic supply of the module is ok Red, lit: Communication with the bus node, respectively with the JC-3xx is not active Red, lit: Hardware failure Red, lit: Software failure Red, shortly OS not valid; update OS flashing: Red;...
Seite 10
Terminal X61 - Description Terminal Digital Signals Point X61.CNTA Counter input A CNTB STEP X61.CNTB Counter input B X61.STEP Stepper motor output "STEP", open-drain Stepper motor output "DIR", X61.DIR open-drain SHLD X61.0V Reference potential for digital and analog signals Terminal Analog Signals Point X61.AI1...
Seite 11
Terminal X62 - Description Terminal Multi-purpose Point inputs/outputs X62.DC24 Infeed of actuator supply DIO1 DIO2 V4.0A DIO3 X62.DIO1 Multi-purpose input/output DIO4 X62.DIO2 Multi-purpose input/output X62.DIO3 Multi-purpose input/output Multi-purpose input/output X62.DIO4 Terminal Serial Interface Point X62.RxD Serial interface RS-232, RxD X62.TxD Serial interface RS-232, TxD X62.D- Serial interface RS-485, D-...
Seite 12
X61 / X62 - Technical Data Analog I/Os: 0 ... 10 V, resolution 12 bits; accuracy > 99 % (of meas. value) Input impedance 100 kΩ; load impedance > 2 kΩ Multi-purpose I/O, operating Acc. to IEC 61131-2 type 3 (E) point 24 V: or IEC 61131-2 (A) Counter inputs:...