Werbung
Verfügbare Sprachen
Verfügbare Sprachen
Cooking Zones Timer
The Cooking Timer Zone function is a countdown that can be
set, also at the same time, on each cooking zone
At the end of the period set, the cooking zones switch off
automatically and the user is notified with a dedicated acoustic
signal.
Activation of the cooking zone timer function
• Touch (press) the Selection/Display area (2) (power level ¹0)
• Press
(6) relating to the cooking zone
Use the symbols
Timer, which is displayed in the Zone/Display (4) during
setting the symbol
(6) is flashing
Note: wait 10 seconds without pressing any other command,
so that the Cooking Zone Timer will start.
Note: by pressing and holding
timer is reset
If desired, repeat the operation for several cooking zones.
Note: each cooking zone can have a different Timer set; in
the display (4) he countdown of the cooking zone selected at
that moment will appear; if no zone is selected, pressing the
Display (4) will display the "STAND-ALONE" Timer
countdown.
The countdown mode is the same as the "STAND-
ALONE" timer one (see previous paragraph "STAND
ALONE" Timer)
When the timer has finished the countdown, an acoustic
signal sounds and the cooking zone switches off.
To switch off the Timer:
• select the cooking zone (2)
• set the duration of the Timer to
Power Limitation
The Power Limitation function allows the product to be used while
limiting its maximum absorption, adjusting the absorbed power in
all active cooking zones, ensuring the hob's total absorbed power
doesn't exceed the set maximum absorption level.
Note: the setting must take place with the hob off, without
pressing the ON/OFF (1) key, when the hob is connected to
the mains, or when the electric mains are reconnected within
the following 2 minutes.
To set the Power Limitation:
- press
(which will be flashing, only for the first 2
minutes after powering of the product)
- continuing to hold down
areas of Selection/Display (2) of the cooking zones, anti-
clockwise starting from the front right zone (FR)
(5) to set the duration of the
(6) , the cooking zone
, using
press, one at a time, all the
• each press will be accompanied by a short audible signal
• once all the Displays (2) have been pressed, it will be
possible to release the key
at this point:
• the Display (2) of the left rear zone (RL) will show in
alternate sequence the symbols
is possible to perform the setting:
select the Display (2-RL) then scroll on the Selection bar (3),
until the symbols "C",and "8",appear the Display (2-FL) will
show the current setting**
0 = 7.4 KW
1 = 4.5 KW
2 = 3.1 KW
** by default the setting is 7.4 KW
To change the Power Limitation setting
• press the Display (2) of the left front area (FL)
• then scroll on the Selection bar (3), to select the new setting
• to save the choice made, press the ON/OFF key (1), for 2
seconds; a prolonged audible signal will be emitted to confirm
the successful setting
Bridge Zones
Thanks to the Bridge function, the cooking zones are able to work
in a combined manner, creating a single zone with the same
power level. This function allows evenly distributed cooking with
large-sized pots and pans.
The front "Master" cooking zone can be used in combination with
the corresponding "Secondary" cooking zone at the back
(to check which zones are equipped with this function, see the
illustrated part of this manual).
To activate the Bridge Function:
(5)
• simultaneously select the two cooking zones you want to
use
• the Display (2) of the "Secondary" cooking zone shows the
symbol " "
• using the Selection bar (3), it will be possible to set the
Level (Power) of exercise, which will be shown in the
Display (2) of the "Master" cooking zone
• to deactivate the Bridge Function simply repeat the same
activation procedure
Note: the Cooking Timer Zone, activated during the Bridge
Function, causes the automatic shut-down of both cooking zones,
as in this case they are considered a single combined area.
USING THE EXTRACTOR FAN
Switch-on
Press (touch) briefly ON/OFF (1) hob/extractor: the symbol
lights up;
continuing to press, all the available functions will become
visible for a few moments, e, after which only the main
ones will remain active; the others can be used, and will
be activated, subsequently, during use of the device.
IMPORTANT: all the available functions will be illuminated
with light intensity, which will become more intense only
when they are activated.
62
"
"
"
"
C
and
0
, indicating that it
Werbung
