elektroautomatik PS 5080-05 A Betriebsanleitung Seite 41

TABLE OF CONTENTS
1
GENERAL
1.1 About this document ......................................4
1.1.1 Retention and use ..........................................4
1.1.2 Copyright ........................................................4
1.1.3 Validity ............................................................4
1.1.4 Symbols and warnings ..................................4
1.2 Warranty .........................................................4
1.3 Limitation of liability ........................................4
1.4 Disposal of equipment ...................................5
1.5 Product key ....................................................5
1.6 Intended usage ..............................................5
1.7 Safety .............................................................6
1.7.1 Safety notices .................................................6
1.7.2 Responsibility of the user...............................6
1.7.3 Responsibility of the operator .......................7
1.7.4 User requirements .........................................7
1.7.5 Alarm signals ..................................................8
1.8 Technical Data ...............................................8
1.8.1 Approved operating conditions ......................8
1.8.2 General technical data ...................................8
1.8.3 Specific technical data ...................................9
1.8.4 Views ............................................................15
1.9 Construction and function ............................18
1.9.1 General description ......................................18
1.9.2 Scope of delivery .........................................18
1.9.3 Accessories ..................................................18
1.9.4 The control panel (HMI) ...............................19
1.9.5 USB port (rear side) .....................................20
1.9.6 Sense connector (remote sensing) .............20
2
INSTALLATION & COMMISSIONING
2.1 Storage .........................................................21
2.1.1 Packaging ....................................................21
2.1.2 Storage .........................................................21
2.2 Unpacking and visual check ........................21
2.3 Installation ....................................................21
2.3.1 Preparation ...................................................21
2.3.2 Installing the device .....................................21
2.3.3 Connection to AC supply .............................22
2.3.4 Connection to DC loads ...............................22
2.3.5 Grounding of the DC output ........................23
2.3.6 Connection of remote sensing ....................23
2.3.7 Connecting the USB port (rear side) ...........24
2.3.8 Initial commission .........................................25
2.3.9 Commission after a firmware update or a
long period of non-use .................................25
EA Elektro-Automatik GmbH
Helmholtzstr. 31-33 • 41747 Viersen
Germany
3
OPERATION AND APPLICATION
3.1
3.2
3.2.1
3.2.2
3.2.3
3.3
3.3.1
3.3.2
3.3.3
3.3.4
3.3.5
3.3.6
3.4
3.4.1
3.4.2
3.4.3
3.4.4
3.4.5
3.4.6
3.4.7
3.5
3.5.1
3.5.2
3.5.3
3.6
3.6.1
3.6.2
3.7
3.7.1
3.7.2
3.7.3
4
SERVICE AND MAINTENANCE
4.1
4.2
4.2.1
4.3
5
CONTACT AND SUPPORT
5.1
5.2
Fon: +49 2162 / 3785-0
Fax: +49 2162 / 16230
PS 5000 A Series
Personal safety ............................................26
Operating modes .........................................26
Voltage regulation / Constant voltage .........26
Current regulation / constant current / current
limiting ..........................................................26
Power regulation / constant power / power
limiting ..........................................................26
Alarm conditions ..........................................27
Power Fail (only with 640 W models) ..........27
Overtemperature ..........................................27
Overvoltage protection.................................27
Overcurrent protection .................................27
Overpower protection ..................................27
Remote sensing ...........................................27
Manual operation .........................................28
Switching the device on ...............................28
Switching the device off ...............................28
Manual adjustment of set values .................28
Manually configure protections ...................29
Switching the DC output on or off ................29
Recall feature ...............................................30
Control panel (HMI) lock ..............................30
Remote control .............................................31
General .........................................................31
Control locations ..........................................31
Remote control via the digital interface .......31
Alarms and supervision ...............................32
Definition of terms ........................................32
Device alarm handling .................................32
Other applications ........................................33
Parallel operation .........................................33
Series connection ........................................33
Operation as battery charger .......................33
Maintenance / cleaning ................................34
Fault finding / diagnosis / repair...................34
Replacing a defect mains fuse ....................34
Firmware updates ........................................34
Repairs .........................................................34
Contact options ............................................34
www.elektroautomatik.de
ea1974@elektroautomatik.de
Page 3