Click-To-Link (Ctl) Intercom; Busy Signal; Receiving Intercom Calls; Pairing And Using A Mobile Phone, Gps Or Mp3 Player - SCHUBERTH SRC SYSTEM PRO Bedienungsanleitung

FOUR-WAY INTERCOM
Pairing
1. Pair Rider 1 to Passenger 2 using Channel "A" (see 6.2a).
2. Pair Rider 3 to Passenger 4 using Channel "A" (see 6.2a).
3. Pair Passenger 2 to Passenger 4 using Channel "B" (see 6.2a).
In this configuration the two passengers (numbered 2 and 4) are each using
two Bluetooth connections:
Calling
1. Make sure all four units are in Standby.
2. Passenger 2 should double-tap v to call Passenger 4.
Wait until audio is heard on both units.
3. Rider 1 should tap v to call Passenger 2.
4. Rider 3 should tap v to call Passenger 4.
IMPORTANT: Four-Way Conference Mode Considerations
During a 4-Way Intercom call, the two passengers who maintain two active connections will not be
able to receive mobile phone calls or GPS instructions as long as the conference call is in progress.
|
SRCS Pro
34

6.3 CLICK-TO-LINK (CTL) INTERCOM

Click-to-Link is a spontaneous, "social" feature of your SRC-System™ PRO.
You can instantly initiate 1-on-1 intercom calls with other riders near
you, without being paired. Think of it as a private channel that you can
set up on-the-go with other riders that you see along the way.
Click-to-Link can be disabled effectively blocking any attempt by a third party to
send a CTL request to you.
Start a CTL call request
v
Tap three times
(search lasts up to 10 sec.)
End a CTL call /
v
Tap
Cancel a CTL call request
When hearing the CTL ringtone:
Accept a CTL call
Tap v or say any word loudly to answer by VOX
While hearing the CTL ringtone:
Reject a CTL call
Remain silent until the ring tone stops or press
two seconds
Enable / Disable CTL
Via the Settings Menu, Cardo Community and the
(Enabled by default) Cardo Smartset App
If other riders are nearby, your next Click-to-Link call may randomly connect to
any of them.

6.4 BUSY SIGNAL

When attempting to establish an Intercom call with another unit that is already
busy, a "busy" signal will be heard. The SRC-System™ Pro is busy while on a phone
call, intercom call with Channels "A" and "B", "1+8" intercom call or CTL call.

6.5 RECEIVING INTERCOM CALLS

If a paired unit tries calling you via Intercom, the call will begin almost instantly.
7. PAIRING AND USING A MOBILE PHONE,
GPS OR MP3 PLAYER
To connect your SRC-System™ PRO to a Bluetooth device you must first pair
them. Once paired, they will automatically recognize each other whenever they
are within range (10m / 33ft).
Your unit has two Bluetooth channels for connection to mobile phones, GPS
devices and music players with A2DP.

7.1 PAIRING BLUETOOTH CHANNELS 1 AND 2

1. Make sure Bluetooth is enabled on your phone/GPS/MP3 player.
2. Check the unit is in Standby (single BLUE flash every 3 seconds).
3. To pair Bluetooth Channel 1 – press
RED and BLUE LEDs begin rapidly alternating.
To pair Bluetooth Channel 2 – press
RED and BLUE LEDs begin rapidly alternating.
v
for
To pair a GPS, when LEDs begin rapidly alternating, tap
4. Search for Bluetooth devices on your phone/GPS/MP3 player by following the
device's instructions.
5. After a few seconds the device will list "SRCS PRO". Select it.
6. If prompted for a PIN or Passkey, enter 0000 (four zeros).
7. The device will confirm that pairing has succeeded and the LED will begin
flashing Blue, once every 3 seconds.
8. If pairing is not completed within 2 minutes, the unit will return to Standby mode.
IMPORTANT!
• If you have paired 2 different mobile phones directly to your SRC-System™ PRO, you
will need to set one as default for making calls.
• If your GPS supports it, you can pair the second mobile phone directly to the GPS and
then pair the GPS to your SRC-System™ PRO, and so connect both mobile phones and
the GPS to your SRC-System™ PRO.
NOTES:
• Not all Bluetooth mobile phones can broadcast Bluetooth Stereo music (A2DP), even if
the phone has an MP3 player function. Consult your mobile phone's User Manual for
more information.
• Not all Bluetooth GPS devices allow connection to Bluetooth audio devices. Consult your
GPS User Manual for more information.
• After pairing, you may need to tap
+ for at least 5 seconds until the
MP3 player
- for at least 5 seconds until the
Up to 1 km Bike-to-Bike
Intercom Range*
Built-in
FM radio
+ .
µ
to connect.
GPS
Mobile phone
& A2DP connectivity
|
SRCS Pro
35